Topics

Anyone have the Grind Customs Lamprey docs?

If you listen to podcasts and you've not discovered it yet, No Guitar Is Safe is a good podcast. They interview a lot of famous and not so famous players. The best part is the host is a damn good player as well and jams with the interviewees. 

Does anyone know if their is a diy Diamond Compressor clone?

Just picked up a Friedman Runt 50 today. I've been GASing for this one for a while. I can't wait for the weekend. (That's the only time I get to play these days)

Anyone know what the yellow component marked 105M is?

It's a Kalamazoo clone with the offset vb from the Timmy. Originally i was going to use the bass control from the Timmy as well. I ended up making it a 3way switch to stabilize the pcb.

Having an issue recording with sonar professional on a laptop. The recording is delayed by a a few hundred ms. And sometimes distorted. It does this whether I use the CPU mic or a Scarlett 2i4 interface. The usage meter on SONAR shows well under 50%.

I'm using an HP laptop with a second gen i7 and the stock Realtek sound card.
I'm assuming that the sound card is the issue but I'm not sure. All drivers have been updated
Any ideas?

PIGTronics Echolution 2 Ultra Pro.
I was trying to decide between this and the Timeline but I went with the smaller footprint. so far I'm digging it.
My only minor complaint is that I wish I could control the dry signal volume. Their is potential for some nice clanging and chorusing sounds but they end up being louder than the bypass volume

This is a Pearl overdrive clone. The only mod i did was to widen the Q. I might socket those caps and try the stock values.
I've only played it for an hour but it seems best to me to use this to push an amp that's already breaking up. I wouldn't use it as a stand alone overdrive into a clean amp.

I would describe it as a cocked wah boost and overdrive. I've gotten some good Boston tones and Some good Slash lead tones with it. If you are into those kinds of tones you should give it a go. That's my 2 cents

This is a Lovepedal Kalamazoo clone. The only change is that I made it mosfet clipping instead of silicone diodes.

This is a Nobels ODR1 clone ( pcb). I was tired of building TS variants and stumbled across this. I'm glad that I did. It does the country thing very nicely. The high end is very detailed but not shrill.

Oshed tube screamer.  Pre voice selects between different input caps and clipping options. Post voice has 150n caps in the center position. The lower and upper positions add 68n caps in parallel to equal 218n.(close to 220n)  the upper position also adds the flat mids from the FD. Everything went great except for the fact that DPDT on off on switches are taller than standard in on switches. Oops!  So I had to set the 9mm on top of the pcb and solder them instead of pushing them into the pcb. Lesson learned.

Does anyone make a Pearl ds-06 clone pcb or have a correct schematic?  The schematic that I found seems to have mistakes. Thanks in advance.

Anyone have a schematic for a Lovepedal Super 6 Stevie mod?  Internet rumor says  it's based on the Timmy but it definitely seems like it's tuned a bit differently.

Does this really work?

http://s.webry.info/sp/houshu.at.webry.info/200604/article_6.html

R5 is 200k. Can I use 220k or 180k?
R6 is 7k5. Is 6k8 ok?
R8 51R. Is either 47R or 100R ok?
Will using these alternative values hurt the "performance" of the circuit? In other words will it not sound as good?
Thanks in advance!

This is one of my favorite octave effects. I built the original Lowrider as well and I must say the 2015 version is much better. The upper octave is cleaner and both lower octave sound a bit "stronger" to me. Definitely worth building.

Finally Oshed my favorite phase shifter the Ross Phaser.
Its mostly stock except that I used 2n7 caps instead of the stock 3n3s. This brightens the sweep a bit.

Has anyone done a Danger Zone demo?  Thanks in advance

Well title says it all its a Madbean Dirtbaby. no mods and it really doesn't need any.