Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Ralfg

Pages: [1] 2 3 ... 13
1
JJs are actually made in the Slovak Republic and I find them to be pretty reliable. I have their rectifier tube in 2 amps and never had a problem. I think Chinese tubes get a bad rap that isnít quite deserved. An amp tech told me that JJs and Chinese tubes are really the only ones made to spec and some of the only tubes you can use for the cathode follower position. Donít know if that is true or not. You could also try a Ruby rectifier tune, itís just a re-labeled Chinese tube but tested for quality. I did have a sovetek and a Mullard (all under the New Sensor) go bad on me.

2
General Questions / Re: Replacing tubes
« on: December 19, 2018, 12:01:06 AM »
Did you try replacing the phase inverted tube? You mentioned it earlier.

3
General Questions / Re: Replacing tubes
« on: December 09, 2018, 01:31:50 AM »
Replacing power tubes in most amps requires that you bias them. I donít know if that amp is cathode biased or not, or how itís set up. So keep that in mind when you are going to do a power tube replacement.

Personally I like JJs for everything power tube.  And for 6L6 I also have used 6L6wxt+ and have liked them. I think... and mind you this is hard to tell... but the JJs I think have more umph.

4
Build Reports / Re: Lone Wolf, Beef and Madness OD's
« on: December 06, 2018, 07:29:36 PM »
Awesome builds! Did Wampler do any mods to the ODR-S?

5
Audio/Video Demos / Re: Headtrip demo
« on: October 19, 2018, 08:48:58 PM »
That is just cool.

6
Tech Help - Projects Page / Re: Moar IC voltages pins 4 and 8 swapped
« on: October 16, 2018, 09:34:34 AM »
Glad you figured it out. Should have suggested reflowing everything.

7
Global Annoucements / Re: Oct. Releases (instead of Sept)
« on: October 15, 2018, 06:42:37 PM »
So, on the Headtrip I've decided to include the SpinCAD file used to make the patches for the project. I'm really hoping people will take advantage of that to start exploring SpinCAD to program their own stuff. It's really pretty easy once you get the hang of it. That doc should be up tomorrow. I still plan on doing an introductory tutorial to SpinCAD before the end of the year. Things is pretty crazy ATM, though.

That is awesome! Iím really glad you are doing that. Iíve been wanting to get into SpinCAD and fv-1 programming, but havenít had the time to learn.

8
Tech Help - Projects Page / Re: Moar IC voltages pins 4 and 8 swapped
« on: October 15, 2018, 12:48:57 PM »
Next thing to check is make sure your power supply is center negative. You can do that by putting the negative of your volt meter leads into the barrel and placing the other on the outside. Make sure it reads +9. Also how are you connecting it to your wires for testing?

9
Tech Help - Projects Page / Re: Moar IC voltages pins 4 and 8 swapped
« on: October 15, 2018, 12:17:52 PM »
Check to see if either the IC is in backwards or you have the ground and +9 volt wire in reverse.

10
Itís hard to say without pictures. It would be good to have a picture of the top and bottom side of the board that would help someone here figure out what is going on. Check your cuts and make sure you are not missing on, can happen pretty easily on vero. And reflow your connections. Look for any solder bridges that might have accidentally happened. Iíd first look at your power section and check if everything is hooked up correctly to you two ICs. Those voltages are way off and it makes me think you are missing a cut, or something is grounding the power.

11
Global Annoucements / Re: Big Release Day! Free Donuts!
« on: August 11, 2018, 08:40:34 AM »
Ordered my UberTuber! Whatís you tube testing process?

12
Open Discussion / Re: Coming up...shop tour - opinions?
« on: August 06, 2018, 06:05:45 PM »
Itís looking like you could do a miniseries. All these sound great to me. Tales from the Bean Cave.

13
Open Discussion / Re: Blackened is the end
« on: August 03, 2018, 04:13:54 PM »
Into obscurity

14
General Questions / Re: Pipsqweek/Ring Mod Diode Switch
« on: August 02, 2018, 10:45:18 PM »
Awesome glad you got it working.  What do the zener diodes do to the sound?

15
General Questions / Re: Pipsqweek/Ring Mod Diode Switch
« on: August 01, 2018, 10:20:10 PM »
Switching sometimes baffles my brain.  My gut says maybe try something like this:


Pages: [1] 2 3 ... 13