Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Soup39

Pages: [1] 2 3 ... 6
1
I think I have a spare Jfet matcher etch board I could throw your way if that helps any.  The other option would be to buy a matched pair from guitarpcb or other sources.

2
Build Reports / Re: Rub a dub Echoplex
« on: May 18, 2018, 07:27:28 AM »
What is the additional jack at the top of the box for?  inquiring minds want  to know  :)

3
Build Reports / Re: Bloodstone Build
« on: March 13, 2018, 10:52:19 AM »
just mouth in hand guts? Still Glory  ;)

question  ;D
swirl first then drill? no worries scratch the swirl?

**Good Catch; edited to include guts.

Swirl first and then painters tape to protect he finish while drilling.  No issues.

4
Build Reports / Bloodstone Build
« on: March 13, 2018, 07:44:07 AM »
I never post build reports, but this one was done for a friend.  The request was for a phaser and maybe something green & orange.   The thing sounds gorgeous, so lush and plenty of phase on tap.  The on/off indicator doubles as the rate indicator and is hidden within the clear shaft pot.  Its hard to tell but there is orange, silver, & green foil layered with  the swirl.







5
check out the PIG/P19, sounds great and the pedal description includes: "Specifically tuned to the sound of a block-buster 1979 album (okay, it's "The Wall") and emulates the "magic" 70's era fuzz pedal"

6
Build Reports / Re: Zirc Jr Build
« on: February 12, 2018, 11:59:23 AM »
Looks terrific,  Gordo!  I really like your choice of knobs, the black really pulls out the little bit of black that's in the swirl.
Thanks for the mention also,  ;).

8
Open Discussion / Re: Envirotex over ink
« on: January 08, 2018, 12:28:44 PM »
My recommendation would be to put it in a frame & wall mount it, get a new backplate.

9
Build Reports / Re: Reverse Engineered Centaur
« on: September 09, 2017, 04:12:42 AM »
Love it well done.  Where did you source those knobs?

10
General Questions / Re: Paint ripping off
« on: September 09, 2017, 03:19:05 AM »
Don't spray the back plate keep it raw.  No ones ever going to see it anyway. ;D

11
General Questions / Re: Grind Customs LFO Board
« on: August 27, 2017, 05:53:48 AM »
Aren't the pads between the rate & depth pots for the switch?  They are labeled sqr/blank/sin.

12
Build Reports / Re: The Super Arcadiator
« on: August 09, 2017, 07:04:39 PM »
I'd be interested in a board.  Do you have a link (& wiring guide). To the arcade buttons used?  What would the pcb cost (I'm in the US)

Thanks,
Jon

13
Open Discussion / Re: Mounting a PCB to an enclosure
« on: June 26, 2017, 10:11:57 AM »
GuitarPCB sells "pcb mounts"  that attach to the PCB and use tape to attach to the enclosure.  http://www.guitarpcb.com/apps/webstore/products/show/6644498

Foam tape is thick enough to act as a standoff AND double sided.

14
Tech Help - Projects Page / Re: Aquaboy double MN3005, pcb, vero?
« on: February 26, 2017, 04:56:33 AM »
Maybe aballens doubler would work for you:

http://oshpark.com/profiles/aballen

1) SocketedBBDDoubler - Verified, for doubling up 2x MN3008 to use in place of an MN3005
2) BBDDoublerV2 - Not verified, but same circuit at #1, just a different layout

15
Open Discussion / Re: Electric Druid Delay
« on: December 21, 2016, 03:35:35 AM »
The linked site also sells the 3080.

Pages: [1] 2 3 ... 6