Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Superstereosix

Pages: [1] 2
1
Global Annoucements / Re: health vs. mbp
« on: May 27, 2018, 04:14:38 AM »
Take care of yourself,  man.
Get well soon.

2
Global Annoucements / Re: 2017 Year-end Wrap-Up
« on: December 21, 2017, 02:49:36 PM »
Thanks for doing what you do Brian.
Whenever I get the hankering to build something MadBean is the first place I check in.

All the best in the new year.

3
Open Discussion / Re: diyguitarpedals update (closing down)
« on: August 08, 2017, 03:45:17 PM »
get well soon James!

4
VFE Projects / Re: Alpha Dog demo
« on: May 30, 2017, 08:35:50 AM »
Cool Beans!  Like the layout of the video.  Can't see where the tiny pots are clocked though when watching in a small window.

5
Global Annoucements / Re: Very sad news
« on: May 30, 2017, 08:16:09 AM »
RIP.
my feelings go out to all.

6
Open Discussion / Re: I lost my best friend
« on: March 25, 2017, 05:26:25 PM »
Condolences.

7
DC seems ok.  A bit low though on both circuits.  2.9 - 2.8V on most pins.  3.2V on pin4 of the metal film.  Bean's got his all up around 3.4 - 3.7V.
Haven't traced yet, but this could be it..
Hmm.  gotta 22ohm 1/2 watt in R5; the supply to the chip. All pins on the 4049 are on the low side of the pdf voltages..
I might have to change that to a 20 or so.. just tack something in parallel to bring it down some..

Might have to wait until tonight, got me some chores to do...

8
Voltages around the chips are pretty much the same,(and close to readings in the pdf) but carbon one is giving me too much fuzz, almost octave like on the decay.  (Almost fuzz factory like if you know what I mean).
 I bypass the buffer and the tone still getting the same issue.  Something's going on around the 4049 I figure.. I don't think it would be the supply, probably one of the amplifier stages.. I think I'll see if I can signal trace through the stages.  All the resistors are carbon (these are older, I've had them since school) except R18.  Check and see if DC is blocked at C10 and C12..  Thinking of replacing the chip. 
Am I headed in the right direction?

9
General Questions / Re: Has anyone done a Danger Zone demo?
« on: June 27, 2016, 08:43:41 PM »
been expecting that...  :P

10
General Questions / Re: Has anyone done a Danger Zone demo?
« on: June 26, 2016, 08:39:08 PM »
Thanks Brian.

11
General Questions / Re: Has anyone done a Danger Zone demo?
« on: June 26, 2016, 03:12:20 PM »
Yeah, I'm looking for a demo too..

12
Cool.  I haven't ordered in a while and was wondering if you were on vacation.  It is vacation time (not for me, but generally I guess).

13
Open Discussion / Re: Mammoth Sale on 3dpt and a Few Other Things
« on: April 23, 2015, 07:20:56 PM »
I've had issues with Mammoth, but they respond well to my inquires.  I won't go into it..

I ordered once with Mklec and they were great.

14
Global Annoucements / Re: 10 years!
« on: December 22, 2014, 08:23:32 PM »
Congrats!

15
Global Annoucements / Re: 12.13 Etcher's Paradise update
« on: July 09, 2014, 07:12:35 AM »
I'm gonna learn to etch me thinks.

Pages: [1] 2