Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - pedalman

Pages: [1] 2 3 ... 15
1
VFE Projects / Relay question
« on: March 26, 2019, 11:24:06 PM »
I had a few of these laying around. Will they work on the pinball ?

2
General Questions / Re: Fuzz Face SI Transitor advice please
« on: March 23, 2019, 05:40:02 PM »
You live in UK?  Jump on thomann and grab one of those t.c. electronic honey pots. Thomann has them for twenty-something bucks.

3
You can also get nylon/plastic hole plugs in various diameters that are very low profile and snap into the hole. Good for a spot that may not need nearby redrilling, makes it look like a hole that will come into play for a future option, planning ahead.
dave

Or you can leave them open as tone ventsTM

Nice. I never thought of a ported pedal. That would let the caps breath a little.

Wouldn't all the electrons fall out ? Jeeze.....

4
Open Discussion / Could be interesting
« on: March 23, 2019, 10:57:33 AM »
This could be interesting

5
Dog food scoop

6
General Questions / Re: Naughty Fish - volume pot wiring
« on: March 16, 2019, 03:03:11 PM »
Think of pad 1&3 as a flowing river
Pad 2 is the bucket scooping up water

7
VFE Projects / Pinball question
« on: March 16, 2019, 02:25:51 PM »
I want to build a pinball so it can be used as it was designed. But was wondering if I could add a loop as well. Let's say I want to modify only a big buff in a petalboard arrangement. Should the loop be on the eq, or the muff?

8
Open Discussion / Re: Plexiglass
« on: March 14, 2019, 04:30:14 PM »
Yep, that's what I'm looking for

9
Open Discussion / Plexiglass
« on: March 14, 2019, 02:17:23 PM »
I've seen plexiglass spacers on some of the enclosures (under the lid)
Does somebody make these, or are they a custom made thing?

10
Open Discussion / Re: Fart'n around at the bench
« on: March 08, 2019, 10:18:59 AM »
It was supposed to be a graphic etch test  but the paper failed

11
Open Discussion / Re: New approach to component organization?
« on: March 08, 2019, 02:47:13 AM »
Back in the day, Blue Diamond Almond made short stubby cans. Perfect for hardware.

Everybody also had the revolving baby food jar wheel of doom

12
Open Discussion / Re: Best Budget Desoldering Station.......?
« on: March 08, 2019, 02:36:24 AM »
Desolder a radio shack pcb and you will see exactly what Brian is talking about. Lol

13
Open Discussion / Re: Best Budget Desoldering Station.......?
« on: March 08, 2019, 02:29:27 AM »
EEV blog does a bunch of cheap reviews

Otherwise I usually trust Circuit Specialist

14
Open Discussion / Fart'n around at the bench
« on: March 08, 2019, 02:24:12 AM »
I was trying out some new printer paper for enclosure etching. Turned out a huge failure, but I had all the gear out for messing around with salt solution so I started playing around with that like a mad scientist with a arc welder

Test 1 was a 6v battery and that was a joke (slight fog)

Test 2 I snapped 2, 9v's together and hit it. This time i masked off a area to see a definite line

At this point I was ready to clean up and go towards a copper sulphate solution tomorrow.
I look over and see soy sauce on the counter.  Hmmm

Test 3, 18v & soy sauce. Believe it or not, it had the best reaction so far and a little quicker.

Tomorrow the copper sulphate comes out along with bench power

15
General Questions / Re: "Starving" a Tonebender Mark III
« on: March 07, 2019, 10:44:27 PM »
I use this a lot, throw in a LCD and your pimp'n it

Pages: [1] 2 3 ... 15