Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - artstomp

Pages: 1 2 [3] 4 5 ... 12
31
Open Discussion / Re: TC Mimiq doubler
« on: January 20, 2017, 05:31:09 AM »
..and Bean..here's another one...Catalibread Nautiliux

https://m.youtube.com/watch?v=q-juRHv04gk

32
Build Reports / Re: Perfboard Rat
« on: January 19, 2017, 10:35:10 PM »
..love the color !!!

33
Tech Help - Projects Page / Re: Glam problems
« on: January 19, 2017, 10:11:33 PM »
..it seems your dry signal is not mixing with the modulated signal that is why you are getting tremolo/vibe sound..

34
General Questions / Re: De Luxe Big Muff
« on: January 11, 2017, 06:44:04 PM »
Thanks Cody..yes the schematic says its a soul preacher and an op amp big muff...i just hope there's an exact project for the vintage deluxe..tnx again Cody

35
General Questions / De Luxe Big Muff
« on: January 11, 2017, 05:00:25 AM »
..is there a De Luxe Big Muff project floating around somewhere ?

36
Tech Help - Etcher's Paradise / FlimFlam 3008
« on: December 12, 2016, 10:30:54 PM »
..will the FlimFlam still be useable as intended if i use MN3008...what modifications should be done to at least extend the delay time....i'll be using my 2 MN3005s for a total recall build and still have an MN3008 collecting dust on my drawer...tnx

37
Tech Help - Etcher's Paradise / Re: SD9 docs link not working.!!!
« on: November 26, 2016, 06:57:13 PM »
..thanks Bean '

38
Tech Help - Etcher's Paradise / SD9 docs link not working.!!!
« on: November 24, 2016, 10:05:28 PM »
SD9 docs link not working..tnx

39
Open Discussion / Re: Tail mod on Boss DM3
« on: September 17, 2016, 11:04:56 PM »
..tnx stecykmi for your concern about decreasing the value of my DM3...i guess i found the answer on the Aquaboy deluxe project..i just need to add a fet switching system...

40
Open Discussion / Tail mod on Boss DM3
« on: September 17, 2016, 07:50:02 AM »
..how would you go about a BOSS DM3 to have a tail mod?..by looking at the schematic my guess is to remove the jfet tansistor connected on pins 10 and 11 of 1571 IC..jumper it then transfer the jfet sw to the input of 1571 IC pin 8...any suggestions from the experts 'round here..tnx in advance..

41
Open Discussion / Pedal Parts Australia will continue to operate
« on: August 26, 2016, 02:27:20 AM »
Just a quick message to let you all know that Pedal Parts Australia will continue to operate under new ownership from Monday 29th August!

http://us3.campaign-archive1.com/?u=ef031356a5a59a5f821f04cbe&id=88f717dd35&e=0e0afe5dbc

42
Open Discussion / Re: Mn3006
« on: July 07, 2016, 10:06:30 AM »
..thank you very much, scruff...that was a load of info my brain could handle...but im learning a lot...by the a ve got a MN3009 i pulled from my Pearl chorus ensemble...i replace it with MN3007 and do some tweaks on some resistors...tnx again

43
Open Discussion / Re: Mn3006
« on: July 06, 2016, 11:45:26 PM »
..tnx Jesse..that was a load of info...so replacing an MN3007 on an existsing flanger pedal would require some parts replacements, too, I guess?..

44
Open Discussion / Mn3006
« on: July 05, 2016, 08:57:08 PM »
..just wondering what will happen if i retrofit an MN3006 ic to MN3007 on a flanger circuit...knowing the MN3006 has a shorter delay time..guyatone ps004 utilizes this ic...tnx for your reply..

45
Build Reports / Re: Aion Fractal (Pearl OD-05)
« on: June 18, 2016, 10:06:09 AM »
..i'm glad that mojo JRC4558 i sent you sounded good on that Pearl OD-05...

Pages: 1 2 [3] 4 5 ... 12