Author Topic: Vero split usable?  (Read 155 times)

Jay.lingelbach

  • Diode Destroyer
  • *
  • Posts: 26
    • View Profile
Vero split usable?
« on: July 11, 2019, 09:25:34 PM »
Iím guessing no. Just confirming thatís the case.




Sent from my iPhone using Tapatalk Pro

vizcities

  • Transistor Tickler
  • **
  • Posts: 89
    • View Profile
Re: Vero split usable?
« Reply #1 on: July 11, 2019, 09:29:05 PM »
If the tracks are intact? Technically yes, but I'd still start over with a new board - veros are finicky enough as it is.

EBK

  • Electron Doctor
  • *****
  • Posts: 1074
  • Eric K.
    • View Profile
Re: Vero split usable?
« Reply #2 on: July 11, 2019, 09:32:53 PM »
Is that a phenolic resin board?
Not affiliated with Oatey, makers of the world's best and most delicious* low tar solder paste. Ask for Oatey -- It's the juiciest!

*Solder paste is not food.  If ingested, seek medical help promptly.

dawson

  • Diode Destroyer
  • *
  • Posts: 20
    • View Profile
Re: Vero split usable?
« Reply #3 on: July 11, 2019, 09:46:16 PM »
Yeah^ what vizcities said- the solder pads &/or tracks (depending on the type of board) are the important part, so as long as you treat it gently, a board that's split in half like that will work just fine, but personally I'd happily trade the 80 cents for a fresh, strong, unabused board.

Now a couple questions for you:
  How did that even happen??
  What are you building?

Jay.lingelbach

  • Diode Destroyer
  • *
  • Posts: 26
    • View Profile
Re: Vero split usable?
« Reply #4 on: July 11, 2019, 09:47:13 PM »
Is that a phenolic resin board?

I honestly have no idea.

It was advertised like this:
6.5x14.5cm Stripboard Veroboard Uncut PCB Platine Single Side Circuit Perf Board


Sent from my iPhone using Tapatalk Pro

Jay.lingelbach

  • Diode Destroyer
  • *
  • Posts: 26
    • View Profile
Re: Vero split usable?
« Reply #5 on: July 11, 2019, 09:48:56 PM »
Yeah^ what vizcities said- the solder pads &/or tracks (depending on the type of board) are the important part, so as long as you treat it gently, a board that's split in half like that will work just fine, but personally I'd happily trade the 80 cents for a fresh, strong, unabused board.

Now a couple questions for you:
  How did that even happen??
  What are you building?

It happened while cutting it. Probably just didnít get deep enough and put too much stress on the board. Building an mxr distortion plus with some wampler mods.

http://2.bp.blogspot.com/-WrOham39S78/UQgbmV5XBOI/AAAAAAAABR4/eEM3oK37nAI/s1600/MXR-Distortion+-w-mods.png


Sent from my iPhone using Tapatalk Pro

EBK

  • Electron Doctor
  • *****
  • Posts: 1074
  • Eric K.
    • View Profile
Re: Vero split usable?
« Reply #6 on: July 11, 2019, 10:03:07 PM »
Is that a phenolic resin board?

I honestly have no idea.

It was advertised like this:
6.5x14.5cm Stripboard Veroboard Uncut PCB Platine Single Side Circuit Perf Board
For comparison, phenolic resin tends to be brown, perhaps slightly reddish orangish (it also gives off a sweet formaldehyde smell when heated), while epoxy resin boards tend to be more yellow/greenish.  These are still in their plastic wrap, but you can see the difference in color:

Phenolic resin, the cheaper of the two, is basically paper and glue, and it has a tendency to separate from itself and from any copper attached to it when subjected to too much stress, either thermal or mechanical.  Epoxy resin (sometimes called FR4) boards are more expensive and harder to cut, but are much more durable and reliable.
Not affiliated with Oatey, makers of the world's best and most delicious* low tar solder paste. Ask for Oatey -- It's the juiciest!

*Solder paste is not food.  If ingested, seek medical help promptly.

dawson

  • Diode Destroyer
  • *
  • Posts: 20
    • View Profile
Re: Vero split usable?
« Reply #7 on: July 12, 2019, 01:54:10 PM »
Thanks^ for the info', EBK, now we all get to learn something- mine are said to be made of "Bakelite," also known as "polyoxybenzylmethylenglycolanhydride" for short, so I'll have my eye out for the higher quality epoxy boards.

Good luck with the Distortion Plus, Jay.lingelbach!

EBK

  • Electron Doctor
  • *****
  • Posts: 1074
  • Eric K.
    • View Profile
Re: Vero split usable?
« Reply #8 on: July 12, 2019, 02:55:16 PM »
mine are said to be made of "Bakelite," also known as "polyoxybenzylmethylenglycolanhydride" for short
To paraphrase Shakespeare:
What's in a name? That which we call polyoxybenzylmethylenglycolanhydride by any other name would smell as sweet (when heated).   ;D
Not affiliated with Oatey, makers of the world's best and most delicious* low tar solder paste. Ask for Oatey -- It's the juiciest!

*Solder paste is not food.  If ingested, seek medical help promptly.

Jay.lingelbach

  • Diode Destroyer
  • *
  • Posts: 26
    • View Profile
Re: Vero split usable?
« Reply #9 on: July 12, 2019, 03:29:38 PM »
mine are said to be made of "Bakelite," also known as "polyoxybenzylmethylenglycolanhydride" for short
To paraphrase Shakespeare:
What's in a name? That which we call polyoxybenzylmethylenglycolanhydride by any other name would smell as sweet (when heated).   ;D

Plus one in thanks for the knowledge!


Sent from my iPhone using Tapatalk Pro