News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - sonolink

#1
Build Reports / Re: boobtube twin revisited
July 31, 2019, 04:34:12 PM
Thanks!! ;)
#2
Build Reports / Re: boobtube twin revisited
July 21, 2019, 11:45:12 AM
Hello again,

A question about the PSU, please. If I want to use only one HV terminal (HVBA), can I just delete C7, R5, HVB1 and HVB2 from the schematic?

Thanks! ;)
#3
Build Reports / Re: Whiskey River: STM800
January 07, 2019, 10:27:08 PM
Oh I see. Thanks anyway :)
#4
Build Reports / Re: Whiskey River: STM800
January 07, 2019, 08:32:16 PM
Did you get the shielded cable from Small Bear too?
#5
Build Reports / Re: Whiskey River: STM800
January 01, 2019, 02:20:41 PM
Great!! ;)
#7
Build Reports / Re: Whiskey River: STM800
December 29, 2018, 09:13:53 PM
Oh I see what you mean. Both jack's GNDs are connected through the enclosure ;)
Thanks

Any idea what those knobs are called? They look cool!! ;)

Cheers
Sono
#8
Build Reports / Re: Whiskey River: STM800
December 29, 2018, 08:16:07 PM
Beautiful build!! One question please: connections on the output jack are Tip only? I can't see the Sleeve/GND connection on the pic...
Cheers
Sono
#9
Build Reports / Re: boobtube twin revisited
November 28, 2018, 11:35:11 AM
Another couple of questions please:

1-The negative terminal of the DC connector would be the final GND terminal (like the green cable to chassis on an amp)?

2-On GrindFX schem "VA" and "VB" (connected to plate resistors) are connected to B+ (190V) right?

3-I've added True Bypass Switch and Clean/Crunch/Lead Channels to the circuit.
Here's the GrindFX schem:


Here's the same schem with the switches:


2-should C13 (right after the Master pot) go after SW2.B? SW4 is supposed to allow the player to choose to place the preamp in front of an amp (through 100k pot) or in its FX loop (through Presence circuit and 1M pot)

3-I just realized I won't be able to use the Opto to switch from Clean to "Dirty", right? :(
If so will a regular Stomp DPDT switch make noise when switching and is there a fix for that?

I really appreciate some input on these questions please :)
Thanks in advance for your time and help!!
Cheers
Sono
#10
Build Reports / Re: boobtube twin revisited
November 27, 2018, 09:14:19 PM
Excellent. Thanks Juan!!! ;)
#11
Build Reports / Re: boobtube twin revisited
November 27, 2018, 02:20:08 PM
One more question please:

I am joining the Clegg PSU to 3 Optotrons on a vero. Both circuits original schems have a diode between 9V and GND. I guess I should put only one diode for the whole thing right? Or should I put one diode for each circuit?
Not sure this makes sense....
#12
Build Reports / Re: boobtube twin revisited
November 26, 2018, 07:30:39 PM
UPDATE: It works now!! :)
There was a bad connection to the Vol. Adj. Once fixed the PSU seems to be now running smooth and I could adjust it to 190V :)

Cheers
Sono
#13
Build Reports / Re: boobtube twin revisited
November 26, 2018, 12:30:07 AM
Hi Juan

I sincerely appreciate your kind offer. I live in Spain and it would probably be the easiest thing to do, but with all due respect, I'd like to fight this one myself (with some support and guidance of course)...I like this beast so much I want to make it mine if you know what I mean :)

So I went back to square one, back to strip board and back to Cleggs design, only adding a diode that is on GrindFX schem, one that bridges 9V to ground right at the start. I'm not sure "bridges" is the correct term but I think you get what I'm saying...excuse my language barrier :)

So I put it together this evening and fired it up and get to read 30V. I tweaked the voltage adjuster and POP went the 2.2uF electrolytic (it was the wrong way around). I replaced it and made sure it was the right way now. Fired it up again and now I get 300V!!

The thing is, when I tweak the pot it won't do much. It stays around 300-350V...of course I don't know if it's because something was blown together with the cap or because I placed something wrong...I guess anything is possible. If there's nothing obvious you can think of, I'll check the resistors, unsolder caps, diodes and ICs, check them and try again tomorrow and report back.

Thanks again for everything :)
Cheers
Sono
#14
Build Reports / Re: boobtube twin revisited
November 23, 2018, 07:13:31 PM
Update: the NE555 went up in smoke :(
Any help troubleshooting very much appreciated. Thanks :)

Cheers
Sono
#15
Build Reports / Re: boobtube twin revisited
November 23, 2018, 06:40:46 PM
Hi again

Sorry for the delay but I got busy with other stuff. I picked up this project again and built the PSU. I use a 1 Spot 9v PSU connected to "9V" and "G" pins of the schem. When I juice it up I read 9v everywhere (Test, HV and 6V terminals).
I've checked the board several times but everything seems correct. Any ideas on what I could be doing wrong?

Thanks in advance for your time and help
Sono