News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - JC103

#1
Cool idea!

Mono in, modultaion fx loop, return to panner, stereo out to two amps. With stereo delays this would sounds awesome.
#2
I have my rig set up for stereo. I have the CE-3 and two Current Lovers that I use frequently. I also just discovered that BYOC had a stereo flanger at one point in time. It used dual BBDs and the phase flip trick on the second output. I've never heard one, but it does sound like an interesting idea. Playing through two Current Lovers in parallel does indeed sound better than just one (mine are in phase). I like the out of phase setting on the CE-3 for achieving that "outside the sound stage" effect. If recorded well, it sounds huge on playback. The CE-3 is quite underrated, but is a lot of fun to play. It is more subtle than a CE-2 (which I use on the right side of the stereo amp set up).

BYOC:

https://buildyourownclone.com/products/analogflanger?_pos=1&_sid=b621a5b3b&_ss=r

byocelectronics.com/flangerscheme.pdf

#3
Open Discussion / Re: Darkhorse SS2/G2 build doc
May 04, 2019, 12:04:12 AM
I'm not sure if anyone ever figured out what brand/style of GE diodes were used in the original. It appears there was an error in the value of that one cap in the initial tracing attempt (100pF vs. 1n). The result was a very dark sounding effect which does not at all sound like the genuine box if played side by side. It is as if the tone control has a range of 1-2 rather than 1-10, there is a ton of top end missing in the clones. Also vf of .26 seemed to be the target for sourcing germs for the circuit. Apparently with the mods done, you are not locked in to such a tight tolerance with the diodes.
#4
Open Discussion / Re: Darkhorse SS2/G2 build doc
May 02, 2019, 02:18:46 AM
I think that fixes the diode dependence issue. You may find other diode references in that thread though. It's a good read. I had a chance to play a real G2 a couple months ago. As you would suspect it is much brighter than all the clones. I find that you can use the Black Horse Duplex Drive SS2 side to EQ the G2 to sound almost identical to a real one. No gain, adjust volume and treble to taste.
#5
Open Discussion / Re: Darkhorse SS2/G2 build doc
May 02, 2019, 02:15:45 AM
From page 5 here: http://www.madbeanpedals.com/forum/index.php?topic=18614.60

Socket these components, and try these subs:

R10- 18k (was 15k)
R11- 100R (was 680R)

C5- 100pF (was 1nF, fixes the dark tone issue)
#6
Open Discussion / Re: THAT Corp parts, how common?
December 31, 2018, 05:24:07 PM
I haven't looked recently but the ubiquitous Boss CS-3 is apparently using a THAT chip for the VCA compression. The good version, the CS-2, used the obsolete BA662 if I remember correctly. These guys cloned it: http://www.openmusiclabs.com/projects/ba662-clone/index.html

I've always wondered if there were other chip options for modernizing a CS-2 style compressor.

#7
Build Reports / Re: Aion Refractor build
December 30, 2018, 10:11:49 PM
Quote from: aion on December 06, 2018, 02:39:25 PM
The resistors are "house brand" for lack of a better term - I get them custom manufactured. I haven't talked much about them much, but they are 0.5% tolerance and would check all the boxes for audiophile grade. They're pricey compared to Xicon or KOA Speer but worth it to make kit building easier (no color codes to read) - and just because they're red!

They're very similar to the ones made by Precision Resistive Products like VFE used to use. It's not that brand, but the resistors themselves are pretty close in specs, if someone wanted a lead on ordering some similar ones.

Just noticed how cool those red resistors look! Attention to detail in these kits is unreal, even the jacks match the Wimas. Thanks to Gordo for the build thread, I have been curious about this project recently. Aion, are those resistors similar to the sausage brown Dale/Vishay brand?
#8
Is that the 2013 version? The full spectrum boost is worth your time.
#9
Open Discussion / Re: Aion Kits: What are those switches?
December 20, 2018, 01:34:16 AM
I'm curious about the tpdt footswitch in particular. I agree, the custom nut is awesome looking!

Have you seen these?

https://lovemyswitches.com/anodized-aluminum-nut-for-foot-switches/
#10
Open Discussion / Aion Kits: What are those switches?
December 18, 2018, 04:39:33 AM
Does anyone know where to source the stomp switches that Aion is using in his new kits?
#11
Cool. Good to know. I guess no one ever builds the 18v lol.
#12
This project is on the to do list (18v specs). The mistake was on your end or an error in the build doc?
#13
Open Discussion / Re: NGD + Opinions Wanted
August 04, 2018, 07:02:37 PM
Stra-dogs from Vineham in Canada. P90's fit for a strat! Just do two, one in the neck, one in the bridge. You'll need a pickguard with no middle position cutout, but hey, you could get a set of three!
#14
Requests / Re: Tone press
July 11, 2018, 09:33:45 PM
Bump. Is there anything special about the fet style blend that Barber used on the TP? Could it be adapted for use with a Boss CS-2 clone?
#15
You may want to cross reference this project with the Metal Zone MT-2 . It's possible there are some similarities (sans mid control). Electric Druid has a decent break down: https://electricdruid.net/boss-mt-2-metal-zone-pedal-analysis/

I can help when it comes time to compare your results with an original Boss MZ-2.

Just to confirm, this is the smd distortion pcb?