News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - princeton

#1
General Questions / Re: 4:1 compressor - VTL5C6?
October 03, 2018, 11:40:44 AM
Thx for your more helpful answer.
#2
General Questions / Re: 4:1 compressor - VTL5C6?
October 03, 2018, 07:38:54 AM
Nobody?
#3
General Questions / 4:1 compressor - VTL5C6?
September 27, 2018, 01:42:17 PM
Hi, would it be possible to use VTL5C6 instead of VTL5C3 in 4:1 compressor? I have no VTL5C3 at hand.
#5
Requests / Re: Power Supply Project
January 11, 2011, 09:31:39 PM
Quote from: madbean on January 08, 2011, 07:09:09 AM
Okay, yeah. I have a basic one drawn up that would be able to 9, 12, 15 or 18 on any output depending on how you populate it. But, it doesn't use a transformer. Rather my idea was to use a 24v/1000mA supply and just break down the voltages with regulators. Neg. voltage could be done with a charge pump.

I've never put it together, though. I'll pull it out and have another look at it.

Is it possible to convert a PC PSU to serve as pedal board supply?
#6
Build Reports / Re: Pork Barrel Build Complete
January 11, 2011, 08:33:33 PM
Quote from: carbonfreeze on January 11, 2011, 06:57:29 AM
Sorry I took so long to reply. I haven't been building for the past several months. But a friend is working on one of these and I made a video demo for him. Check it out. My amp is a little gainy, but no, I haven't noticed any distortion from pick attack. I think eniacmike has a good idea about the trim pot.

Here's the video demo.

http://www.youtube.com/watch?v=qnWcsXoLdLs

Nice one, sounds so Purple Rain-y. Very useful video. Thx
#7
Open Discussion / Re: Merry Christmas, Y'all!
December 24, 2010, 03:42:45 PM
Merry Christmas!
#8
Requests / Re: Sub-mini tube amps
December 19, 2010, 10:12:44 PM
Very interested! Thumbs up.
#9
Build Reports / Re: Sunking
December 18, 2010, 10:55:53 PM
#10
Build Reports / Re: Sunking
December 18, 2010, 10:35:19 PM
Very nice build. Sehr schön und ordentlich. So muß es sein.  :)  I've not seen ICL7660SCPA at Banzai. Where did you get it?
#11
Requests / Tone press
December 15, 2010, 07:48:51 PM
If not already requested by someone  I would like to make a request. The Barber Tone Press.
#12
Open Discussion / Re: POST YOUR PEDALBOARD / GEAR!
December 15, 2010, 07:46:07 PM
Quote from: eniacmike on December 15, 2010, 02:31:37 PM
I am a compressor-holic I have 4 and the tone press is the best I have found. barber makes really good stuff too. inspirational build quality. The blend knob is a great feature for a compressor because you can keep your attack but retain the supernatural sustain.
Quote from: jackbart1960 on December 15, 2010, 03:09:23 PM
Quote from: gtr2 on December 15, 2010, 01:30:45 PM
The tone press has been showing up in a few of these boards...
Still some of the best non DIY money spent. It's been with me for about two years+ and it's always been in the first slot since. The parallel mix knob is the key. As a Tele player a comp is a given and I went through a few 'till this one stuck. Does what it does without sound being to rubbery(word even?).
Peace. J.J.B.
Edit: Mike I didn't see your post. What he said. ;D

blend knob mixes compressed and uncompressed signal? parallel compression in a guitar pedal? nice. I need to visit Requests thread :-°  bye
#13
Build Reports / Re: Aristocrat
December 11, 2010, 12:53:09 PM
This baby sounds awesome. Thx for posting the demo. One of my next builds. Btw. fancy socks  ;D
#14
Sounds great. Thx
#15
Build Reports / Re: Serendipity Demo
December 09, 2010, 01:11:21 PM
I'm glad that you all like it and found it useful. Thx