This will sound like a very noob question that might call into question the wisdom of starting this project (never stopped me before), but before I smoke $36 worth of BBD chips, the Tour bus runs 18v DC, not AC correct?
Yes, it is powered by 18v DC and is wired for positive ground.
Quote from: benny_profane on July 04, 2022, 05:37:50 PM
Yes, it is powered by 18v DC and is wired for positive ground.
All the DIY pedals I've built require DC voltage. I've seen many AC casualties.
Only ac pedals I'm aware of are factory made relics from waaay back(like Les Paul still touring..) that were just adaptations of rack units to put on stage to replicate the fun they had in the studio.
If I recall the Uber tuber requires an AC adapter. Think I also remember a video tha Wampler did a while back where he plugged an ac adapter into a non-AC pedal. Fireworks
Quote from: BryGuy on July 04, 2022, 07:17:25 PM
If I recall the Uber tuber requires an AC adapter. Think I also remember a video tha Wampler did a while back where he plugged an ac adapter into a non-AC pedal. Fireworks
I thought I was losing my mind for a Monet there: The Dunlop ECB004US AC adapter provides 18VDC @ 500mA of current
Sent from my iPhone using Tapatalk
Thanks for the reply All. I was 90% sure, but being an old big box EHX circuit, needed the final affirmation. The Hapalochlaena from DeadEnd fx requires an 18v AC power supply.
Quote from: 3knobfury on July 04, 2022, 10:37:24 PM
Thanks for the reply All. I was 90% sure, but being an old big box EHX circuit, needed the final affirmation. The Hapalochlaena from DeadEnd fx requires an 18v AC power supply.
How does that get accomplished, is there an adapter I guess?
Sent from my iPhone using Tapatalk
Quote from: jimilee on July 05, 2022, 02:49:46 PM
Quote from: 3knobfury on July 04, 2022, 10:37:24 PM
Thanks for the reply All. I was 90% sure, but being an old big box EHX circuit, needed the final affirmation. The Hapalochlaena from DeadEnd fx requires an 18v AC power supply.
How does that get accomplished, is there an adapter I guess?
Sent from my iPhone using Tapatalk
I actually had to make one. I found an 18v AC wall wart for the Ring security system that I added a 2.1mm plug to. I have heard of others using laptop power cables to power theirs.
On other notes for power requirements.. 1 should ALWAYS recheck what's written on a capacitor. I somehow had my minor lysdexia kick in(normally it's outgoing, IE words typed/written backwards) and thought the voltage rating and temp rating were inverted... ::)
4v cap+18v=electric popcorn :o
Testing my IC sockets kept getting 3.6 to 4.2 volt readings.. then POWWW! the 470uf blew was a 4 volt max 85 C temp not 85v....
I've used an old printer PSU for a 5~6watt headphone amp. If there's wires it can be red-neck engineered.
Quote from: jimilee on July 05, 2022, 02:49:46 PM
How does that get accomplished, is there an adapter I guess?
Typically, you could (at the cheapest level) use some 1N400X diodes to smooth the AC. Another option would be to use a FWBR and some filtering caps.
For the DEFX project noted above, the AC is smoothed, filtered, and fed into regulators to provide + and - 15VDC. Its in the schematic if you want to have a look.
Sent from my iPhone using Tapatalk
Aion's L5 pre-amp uses 9V AC. I have that adaptor stored in a special box with a skull and crossbones on it ;D