News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - mjcyates

#1
General Questions / 9V Supply Schematic Questions
May 11, 2021, 12:30:39 PM
Below is a sampling of 9v supply schematic values from various pedals. Obviously all are basically the same, however, they all have slight differences.

Polarity Diode   Resistor   Film Cap   Electro Cap   Resistor   Resistor   Electro Cap
1N5817                -                -           100uf           10k           10k           47uf
1n4003              91r        -           100uf           10k           10k           47uf
1n4003              91r        -           100uf           10k           10k           47uf
1N5817              27r        -           220uf           10k           10k           220uf
1N5817                -                -           100uf           10k           10k           100uf
1N5817                -                -           100uf           47k           47k           100uf
1N5817                -             100n   47uf                   10k           10k           47uf
1N5817                -                -           47uf                   8k2           10k           47uf
1N5817                  -                -           100uf           47k           47k           100uf
1N5817              33r        -           100uf           10k           10k           47uf
1N5817                -             100n   47uf                   100k           100k           10uf
1N5817                -                -           220uf           10k           10k           220uf
1N5817                -                -           100uf           10k           10k           10uf

I know diode is for polarity protection, I know the electros are for power noise filtering, I know the 2 resistors form a voltage divider, I don't know why some include a small value resistor after the diode (usually less than 1k) and some include a film cap (usually 100n). Is there a best practice/standardized power section or are all of these pretty much the same? Just trying to learn a little.
#2
Build Reports / Re: Superbolt/Morning Glory Kicad
April 24, 2020, 02:24:20 AM
Very cool!
#3
Dragonbeard ordered! Thanks Brian.
#4
Build Reports / Re: My KOT
March 19, 2020, 11:30:04 PM
Small Bear, its good stuff

1 x #24 Pre-Bond, Colors, 50 Ft. Spool
(Colors: Black)
#5
Build Reports / Re: My KOT
March 19, 2020, 09:49:56 PM
Thanks! I take that as a high compliment as Juan's stuff is always top notch.
#6
Build Reports / My KOT
March 19, 2020, 03:46:23 PM
Here is my latest build. KOT using pedalpcb Paragon Mini. Built according to stock BOM.



#7
General Questions / Re: Aion Oceanid
January 03, 2020, 07:24:20 PM
I just recently built this using the online BOM and yes only 2 2.2uf caps and both are electros
#8
Very nice! That board makes for a tidy build.
#9
Build Reports / Re: Broadcaster (Hudson Broadcast OD)
December 25, 2019, 06:59:12 PM
Very nice!
#10
Build Reports / Re: Poor Man's Flint
December 25, 2019, 06:58:25 PM
QuoteI dig that. The knobs really set it off I think.

Thanks, yeah I think the knobs look good on this enclosure, actually those have been my go to knobs for all of my recent builds.

QuoteGood squeeze there... nice black understated enclosure!  8)
Thanks!

QuoteNice job! I've been looking at those enclosures. I hope they come out with other stock finishes.

Thanks! The enclosures are very nice. Lately I have only been using black or white so I am covered but other colors would be nice.

QuoteI didn't realize those enclosures look so cool.  I think they're also available in white and silver (and perhaps natural?).  Nice build!

Thanks, yeah pretty cool enclosure and yes they are available in white and silver.

QuoteGood looking build! How are the effects situated? Is the tremolo only in the wet reverb signal, or is it after the reverb and dry signals mix together?

Thanks. Reverb into tremolo. Rub-a-dub directly into the input of the Trem.


#11
Build Reports / Poor Man's Flint
December 24, 2019, 07:14:02 PM

Rub-a-Dub Reverb into EA Trem with toggle switch to defeat the trem. Built in Gorva enclosure from LMS. Guts aren't pretty but it works!










#12
Open Discussion / LMS Gorva Enclosure
December 20, 2019, 03:09:00 PM
Don't know if anyone has tried the new Gorva enclosures from Lawrence's shop. I ordered one to try. They are very nice. A little expensive but I think worth it for something you want to look professional. I am going to try to combine my Rub-a-Dub and EA Trem for a Flint type of pedal. I will post if it works out.
#13
Build Reports / Re: Solar Flare - a FauxJo adventure
September 02, 2019, 11:11:22 PM
One of the coolest pedals I have ever seen!
#14
Build Reports / Re: VFE-MB Modular Mini Mega
July 19, 2019, 12:14:03 PM
Very nice!
#15
Open Discussion / Re: New Pedal Storage Day
July 19, 2019, 12:07:44 PM
Perfect! I always like finding ways to use things not for their intended purpose.