Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Jebus

Pages: [1] 2 3 ... 20
Open Discussion / Re: PPP enclosures for cheap!
« on: May 06, 2017, 01:44:34 AM »
Tried to order various amounts of enclosures but the shipping rates are ridiculous..  ;D ;D

Tech Help - Projects Page / Re: Runt LED Setup...
« on: March 08, 2017, 10:53:20 AM »
For the current version of the RUNT, I'm seeing a pad for the LED, and a 4k7 resistor in r11. My assumption is that the negative of the LED connects to the 3PDT stomp (same as the baby board guide), but the positive goes to the LED pad and I don't need to mess with a resistor (as it will already be on the board).

Can anyone verify?

Sounds correct to me. :) You can always verify this type of thing by looking at the schematic. 9V -> current limiting resistor -> LED -> switching ground (CLR and LED can be the other way around also).

General Questions / Re: FV-1 Chips
« on: March 08, 2017, 12:38:15 AM »
Weird, never had a single wrong or missing component from Banzai. And the customer support has been really helpful, only bit on the slow side. :D

I've done probably ten orders from them.

Open Discussion / Re: Electric Druid Delay
« on: March 05, 2017, 04:39:09 AM »
Has anyone found / recorded any demos of this? I'm interested (tap tempo delay would be nice addition), but would prefer to hear some sounds before ordering the board. :)

General Questions / Re: What does a P6KE120 diode do?
« on: March 01, 2017, 03:51:06 PM »
If you are looking to find out what it does in general a datasheet is good place to start:

General Questions / Re: 3pdt w LED ring
« on: February 22, 2017, 11:18:46 AM »
I'm in if we can get people from Europe. Hate drilling holes for leds. :D

Get alligator wire so you can hook up the jacks temporarily. :)

So it doesn't matter the orientation, I can just fit it any ways it drops in? Looking at the trace on the back, it looks like I need to complete the circuit path, with the inductor legs.

The orientation doesnt matter. Just check that its completing the circuit (so the legs are on the different traces, ie not shorting). :)

Like Sonnyboy wrote, the different pins are just meant for different shaped inductors.

Audio probe is always my go to -debugging method in cases like this. :)

Open Discussion / Re: A good source for...
« on: February 09, 2017, 07:21:07 PM »
BanzaiMusic in Germany has all of those, but the prices are bit high and I don't know how much shipping is to other side of the pond.

Never gotten any bad stuff from them though. :)

Tech Help - Projects Page / Re: Pork Barrel clock noise
« on: February 09, 2017, 06:49:06 PM »
Guess I'll have to rebox in a 1590BB :(

No need for that. Start by moving the wires around like sturgeo mentioned. You might find spot where it doesn't tic at all. Try moving them as far as possible from clock (IC3). If that doesn't help then you can try shielded wires for input and output (the shield connected to ground on one end, nowhere on the other).

General Questions / Re: Waterslide Laser decals?
« on: February 08, 2017, 08:53:18 PM »
I've tried couple different ones for laser. The best I've tested so far I've bought from local arts and crafts shop. The brand is "Holi" and they are meant for scale models. The cost is ridiculous (like 5+ euros per paper or something like that).

All the no-name ones from eBay that I've tested so far are really hard to use. Either you need to soak it forever, or the laser "doesn't stick" when you apply clear coat / Envirotex or they rip up super easy and get wrinkled.

If someone know decent one from eBay let me know. :)

Open Discussion / Re: Today's Repair.
« on: February 08, 2017, 08:23:33 PM »
Hah, never seen one of these before. The board looks really good and well organized. :)

Tech Help - Projects Page / Re: The Pig Butt...from HELL!
« on: February 07, 2017, 08:25:45 AM »
The L is the connection for the switching ground for the led. If its not connected the led wont light up.

I would suggest you to build audio probe:

For me that is the easiest way to debug pedal that has no signal at all. In matter of minutes you will locate which is the amplifier stage that has signal at input but not in the output. :)

General Questions / Re: Drill template prints too small
« on: February 07, 2017, 03:04:28 AM »
There might also be option called "fit to page". Take that off also. :)

Pages: [1] 2 3 ... 20