Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - DLW

Pages: [1] 2 3 ... 9
1
Tech Help - Projects Page / Pepper Spray Q2
« on: January 16, 2020, 10:29:10 PM »
Is the build doc correct? The schematic and BOM say 2N3965. However, the board appears to use an NPN (2N3565) and other Percolator schematics do, as well. Confused.

2
Open Discussion / Re: Cheap DPDT
« on: January 10, 2020, 09:42:01 PM »
The "Dailywell Electronics" DPDTs that Tayda sell are really nice, as well... https://www.taydaelectronics.com/electromechanical/switches-key-pad/toggle-switch/mini-toggle-switch-1m-series-dpdt-on-on-short-lever.html

I think compete with Taiway switch quality for less than half the price.

3
General Questions / Re: Etcher's paradise to EAGLE (Gravity Wave)
« on: December 14, 2019, 03:57:57 PM »
The schematics are freely available. Make an Eagle layout.

4
Open Discussion / Re: Tayda still slipping...
« on: November 22, 2019, 09:26:10 PM »
I don't mean to be pedantic, but Tayda is based out of Thailand, not Taiwan. Also, the implication that Taiwanese manufactured products are low quality is not entirely accurate. Taiwanese manufacturing is almost universally better than Chinese (which is likely the true origin of much of Tayda's knockoff parts).

6
Open Discussion / Re: Tragedy at home
« on: November 03, 2019, 09:14:21 AM »
I'm sorry to hear that. That is awful :(

I had to say goodbye to my cat last Thursday. Pets are family.

7
Build Reports / Re: POLYPHASE
« on: September 19, 2019, 04:13:22 PM »
Looks and sounds great!

8
How Do I? Beginner's Paradise. / Re: Removing enclosure painted design
« on: September 19, 2019, 05:34:10 AM »
Isopropyl will not harm the powder coat. I'd try that first.

Acetone will damage the powder coat finish - might not take it off completely, but it will certainly dull the finish.

9
Very nice! I built one of these, too. It's a fun pedal to tweak!

10
This is a really nice sounding pedal. It's fun to tweak.

Nice job on the build. Very clean!

11
Build Reports / Re: Build Report Bonanza
« on: August 31, 2019, 05:42:42 AM »
Great collection! Thanks for posting these :)

12
Build Reports / Re: Benzin VH4- Get your chug on!
« on: August 16, 2019, 06:01:44 AM »
Very clean build. I like the design, as well... what is the function of the 3rd jack?

13
VFE Projects / Re: Homing Missile Build Doc?
« on: August 13, 2019, 07:05:08 PM »
Unless somebody has a better suggestion, I would follow what is written on the board. The "pwr" components have been 100n MLCC 2.5mm capacitors on other VFE boards that I've built. I assume it is the same here.

14
VFE Projects / Re: Yodeler Schematic
« on: August 13, 2019, 07:08:07 AM »
Finally finished the project (waited to accumulate parts for a Mouser order). Works like a charm! Thanks for the help everyone :)


15
Open Discussion / Re: 1590B Top-Mounted Jacks
« on: August 12, 2019, 07:47:42 PM »
Thanks for sharing! I'll print it this week to try it out.

Pages: [1] 2 3 ... 9