Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - murdog47

Pages: [1] 2 3 ... 28
1
Open Discussion / Re: Why do I want to buy every pcb out there?
« on: December 18, 2014, 04:32:45 PM »
You think pedals are bad...stay away from amplifiers! Talk about an addiction!

2
I've always enjoyed a klon in front of an OCD. I run the Klon clean and use the OCD volume at noon and add gain in from there

3
General Questions / Re: Sunking 2 - zener diode and 10r resistor question
« on: December 15, 2014, 12:15:32 PM »
I don't know if there was ever a definite answer on this. I ended up replacing the 10R with a jumper. It works fine now with or without the zener in the circuit.

4
Tech Help - Projects Page / Re: Why am I not getting signal past Q1?
« on: November 27, 2014, 10:09:34 AM »
Pinout is correct. I'll try swapping the BS170

5
Tech Help - Projects Page / Why am I not getting signal past Q1?
« on: November 26, 2014, 05:21:42 PM »
I did a layout of the RAH circuit and am not getting signal past the gate of Q1. Here is my scheme and layout. Anyone?




6
Might just be the 3pdt. I had a bad one that gave a pop when engaged. I could feel the difference between the bad one and a good one. Give it a push with your finger, see if you feel two clicks instead of the usual single click. I changed out the switch and the pop was gone.

7
Build Reports / Re: Ninblendo - Nintendo themed Fender Blender from JMK
« on: November 15, 2014, 03:18:55 PM »
Up Up Down Down Left Right Left Right B A Select Start

8
Open Discussion / To anyone who bought a BMP Board from me
« on: October 09, 2014, 04:37:55 PM »
I have found 4 of 30 boards that have a manufacturer error. If you bought a BMP board from me labeled "Little Miss Muffet" and are only getting bypass signal, lug 2 of the volume/level pot is grounded. You need to disconnect  the middle leg of the pot from the board completely and wire it directly to the "Output" on you 3PDT. Shoot me a PM if this doesn't make sense and I'll walk you through it. Sorry if this affects anyone.

9
The current version of the Sunking 2 schematic shows that 10R resistor as 1/2W.  Were you using a 1/4W resistor?

Nope 1/2W

10
Still not sure with the voltages I'm reading why the heck R32 would be burning up like that. And why I haven't seen more people having the same issue. Must be a gremlin in there somewhere. A Klon curse if you will  ;D



11
Jumpered R32 problem solved. Voltages all look good. Not sure what the issue is/was. Sounds good now  :)

12
Pulled D3.....R32 still smoking

13
Just fired up my buffered bypass Sunking II and it also set the 10R ablaze! I'll try the jumper.

14
Tech Help - Projects Page / Re: Green bean help?
« on: September 24, 2014, 03:34:56 AM »
We have lift off.  Thank you so much.  Your wisdom is invaluable and I appreciate it so much.  After it's all boxed up I'll post a video.  I believe the culprit was either a cold joint or the tiniest of solder bridges that I found.  I'm so excited.  Y'all helped me finish my first build!

Congrats!  :) :) :)

15
Tech Help - Projects Page / Re: Green bean help?
« on: September 23, 2014, 04:30:52 PM »
I feel like I missed something.  Is there an LED and a CLR between your power jack and your 3PDT footswitch?

I think there is we just can't see it in the picture.

Pages: [1] 2 3 ... 28