Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - dfine22

Pages: [1]
1
Build Reports / Cherry Bomb
« on: March 03, 2013, 05:43:54 AM »
Came out great looks and sound wise. I love it! BC109's



2
Tech Help - Projects Page / Collosalous Help!
« on: February 28, 2013, 11:25:56 AM »
I built the board according to the layout but haven't boxed it up yet and then noticed that Brian has a update regarding  a diode change to 1n5817 and 100uf for C26. He indicates that his helped with the clock noise on his prototype only.  Now I am confused.
Should I leave it stock or make the changes in the update.
Thanks, David

3
Tech Help - Projects Page / LED Orientation for Boneyard
« on: April 28, 2012, 02:04:15 PM »
I want to get the orientation of the LED's on the boneyard correct and I forget. Square pad (+)?

4
Tech Help - Projects Page / Weener Q1 Orientation
« on: February 27, 2012, 01:14:08 PM »
Could someone help me with the orientation of Q1 in the Weener Wah. Thanks

5
Build Reports / Weener Wah - Q1 orientation
« on: February 27, 2012, 12:59:00 PM »
Can someone help me with the orientation of Q1 on the Weener please and thanks

6
Open Discussion / Clipping section on Uproar
« on: December 21, 2011, 06:11:00 AM »
I wanted a little help understanding the clipping section on the Uproar circuit.  Basically I wanted to remove a pair of diodes to reduce the amount of clipping and I am not sure which pairs to do.  I have it set up like the build document dictates. Thanks for any help.

7
Build Reports / Low Rider
« on: October 29, 2011, 06:49:44 PM »
First MB build post. Used both C10, 12 mods. Hvent really cranked it up too much yet but what I heard I liked so far.




8
Tech Help - Projects Page / Low Rider 9V pad (s)
« on: October 15, 2011, 05:48:14 AM »
I just finished building a Low Rider.  Why are there 2 9V pads on the board. Is one for the LED? Thanks

9
Mods / Retrograde Mod - increase octave up?
« on: September 28, 2011, 04:09:20 AM »
Anybody have an idea for component change to increase the octave up effect of the retrograde.  I think it is a bit too subtle for me. Thanks

10
Tech Help - Projects Page / Chunk Chunk Gain and Volume pots do not work
« on: September 19, 2011, 06:49:15 AM »
Hello, just build a chunk chunk. Presence and  BMT work fine however volume and gain pots do not do anything.  Trannies are biased fine. Cant figure it out. Any help would be great. Thanks

11
Tech Help - Projects Page / Chunk Chunk Biasing
« on: August 11, 2011, 04:10:48 AM »
Just built a Chunk Chunk.  Works OK with the exception of I cannot bias T2. No matter how I turn the trimmer, I still get the same reading (about 9V) on the drain.  Thinking it may be a bad trimmer but unlikely.  I need some help. Thanks, David :'(

12
General Questions / Choosing Resistors?
« on: February 25, 2011, 05:09:43 AM »
Hello,  I am attempting to build my first pedal (Firebomb).  I have modded a few pedals previously.  I am sure that this question has been addressed a thousand times before however which is the best choice for resistors ( metal film or carbon comp). Thanks

13
General Questions / Eliminate 9V Battery?
« on: February 19, 2011, 10:05:09 AM »
Hello, Newbie to pedal building.  I will be building a new firebomb and would like to eliminate the battery source.  Will the jack serve as a ground as I have noticed that w/out the battery clip there is no ground going to the jack?  Thanks

Pages: [1]