Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sirbergersworth

Pages: [1] 2 3 ... 9
1
Open Discussion / Re: Auto wah type filter with reverse?
« on: July 29, 2018, 11:26:30 AM »
Doesnít seem he wants a reversible sweep (up or down). He wants the envelope to act in reverse. Gotta be something like that out there. Can you do something similar with the slow gear?


Sent from my iPhone using Tapatalk

2
Tech Help - Projects Page / Re: Sunking
« on: April 22, 2016, 12:25:39 PM »
Thank you

3
Tech Help - Projects Page / Re: Sunking
« on: April 22, 2016, 07:31:38 AM »
Anyone. Bueler?

4
Tech Help - Projects Page / Sunking
« on: April 21, 2016, 02:09:00 PM »
What are the differences between a Sunking II board and a Sunking 2015 board?
I cannot find the build doc for the Sunking II but I have the build doc for the Sunking 2015.

Thanks in advance,
Rob

5
Open Discussion / AmpTweaker Tight Metal
« on: April 19, 2016, 06:08:14 AM »
Does anyone know where I can find the build docs for this board?

Thanks in advance for your help.


6
Build Reports / Tube Driver
« on: April 18, 2015, 11:54:16 AM »
Did you try the 12BH7 yet? Interested in your results.

7
Build Reports / Tube Driver
« on: March 17, 2015, 03:54:03 PM »
A few 12BH7 I found in an old organ.
They are about 5.8 mm tall. That measurement is taken of glass only. no pins.



Sent from my iPad using Tapatalk

8
Build Reports / Re: Tube Driver
« on: March 15, 2015, 07:20:21 AM »
very cool build

I have some 60's 12BH7's from an old hammond organ. I would definitly trade you one or some for this pedal. lmao. seriously, I would trade one or some for something.

9
Build Reports / Re: Mutron III (GGG Neutron
« on: December 19, 2014, 07:32:13 PM »
Thanks. I am really happy with the sound. I am working on a design for the laser engraver now. hopefully we can get to it next week.


Sent from my iPad using Tapatalk

10
Build Reports / Mutron III (GGG Neutron
« on: December 17, 2014, 10:20:45 AM »
I have had this board for at least 3 years. It was actually given to me by JD as thanks for shipping a kit back to him that he had inadvertently sent to my address. I had read about it a lot on forums and such and how it is a pain to build and get working well. I waited as long as I could, lol. I wanted to get my wiring a little neater on other builds before I tackled the tons of wires this thing needs.
I used CLM6000 optocouplers in the end. I tried the H11F3 and the H11F1 also. The H11F's just did not sound as good. The filter seemed to have a very fast open and shut. I wanted a smoother and longer sweeps. I used a 10 turn 10k trimmer for Rx and made a little daughter board for it. I also used solid wire. A first for me. Orange LED with a bit of a tapered hole to show a little of the bare aluminum.
It took quite some time to get Rx dialed in to sound good on all three filter settings. But, in the end, it sounds great.
One glitch. the gain pots rotation is backwards, but that is an easy fix.
I have been looking for a reason to use one of these Hex shaped hammond enclosures for a while also. This one was going to be for a 2 in 1 but this is a much nicer fit. I bought the factory finished textured black. Now, I need to figure out how to label it. I may bring it to a laser engraver.
Thanks for looking.





Sent from my iPad using Tapatalk

11
Build Reports / Cornish Buffer
« on: December 11, 2014, 08:07:00 PM »
Sirbergersworth - that's really neat wiring for vero! Do you find you use the switch much?

Thanks for the complement. wiring is only neat because there is no pot. lol
I used it quite often at first to see where I wanted it in my chain. Now, not so much. It is nice to be able to hear your rig buffered vs non buffered.


Sent from my iPad using Tapatalk

12
Build Reports / Cornish Buffer
« on: December 09, 2014, 07:07:35 PM »
Here is a Cornish buffer build I did on vero with a switch. I used a toggle since it sits under pedalboard and the switch body is much smaller than a stomp switch. The encloser is 2" x 4" x 1".
Great buffer.

13
Build Reports / Cornish Buffer
« on: December 07, 2014, 11:01:10 PM »
That looks awesome!
I built one on vero and put it in a tiny little box also.
Which schematic did you use? I have seen a few different schematics with a few different values here or there. I really like it but always wonder if mine is correct. I think I used a layout from tagboard


Sent from my iPad using Tapatalk

14
Build Reports / Re: EHX Holy Grail - Rehouse
« on: October 24, 2014, 04:31:10 PM »
Looks great

15
Build Reports / Re: Serendipity Build
« on: October 20, 2014, 04:55:06 PM »
Great build of a awesome pedal.

Pages: [1] 2 3 ... 9