Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Tremster

Pages: [1] 2 3 ... 35
1
Build Reports / Re: Secret Invasion Preamp
« on: October 17, 2021, 04:03:02 AM »
Looking good!

PedalPCB's waste of space is a mystery to me, though. A booster with just a handful of parts, and you'd hardly get it in a 1590B enclosure.

2
Open Discussion / Re: Ten knobs
« on: October 07, 2021, 05:06:09 AM »
Super Hard On or FatPants
Orange Squeezer
Rangemaster
Meathead
Boss OD1
Heartthrob Tremolo
Runoffgroove Tri-Vibe

3
Open Discussion / Re: New wave of "lawsuit" guitars?
« on: August 05, 2021, 01:16:33 AM »
Necro bump.

Gibson is now suing Mojo Hand FX over the name "Mister O" phaser, which could be mistaken for "Maestro".
https://www.gearnews.com/gibson-serves-mojo-hand-fx-with-cease-and-desist-over-mister-o-pedal-name/

4
Build Reports / Re: The Dad Joke
« on: July 16, 2021, 02:55:35 AM »
Tehehe.

5
Open Discussion / Re: A klon just sold for 3500!
« on: June 09, 2021, 12:18:17 PM »
TC Electronic just introduced their Klon:
https://www.tcelectronic.com/product.html?modelCode=P0EBW
Around 60 $. This will sell like hot cakes.

6
General Questions / Re: Jubal Orange Goblin BOM
« on: April 19, 2021, 06:50:36 AM »
I have it. PM me your email address.

7
Open Discussion / Re: Need help with Muff diagram / Mojo Hand Colossus
« on: March 18, 2021, 07:54:04 AM »
Whoa!
Thank you very much!

8
Madbean Sparkplug has outlived any other overdrive on my board.

9
Open Discussion / Need help with Muff diagram / Mojo Hand Colossus
« on: March 11, 2021, 05:58:59 AM »
Dear forum,

I don't feel confident enough with my diagram reading skills, any help would be appreciated.
A friend asked me to build a Mojo Hand Colossus (=a variant of a Russian Muff with mids control and an input cap switch), he had an original years ago.
I can't find a PCB for it, but I have a Fuzzdog BMP board that should do fine: https://shop.pedalparts.co.uk/Big_Muff_Pi/p847124_20010593.aspx
The schematic is in the BOM on page 3: http://pedalparts.co.uk/docs/BMP2018.pdf

The Colossus schematic is on the Kit Rae Muff page: http://www.bigmuffpage.com/Big_Muff_Pi_versions_schematics_part4.html:



The question is (parts numbers are different):
How do I match this bit from the Kit Rae schematic

with this bit from the Fuzzdog schematic


Where does Kit Rae's C14 go on the PCB??
Kit Rae's C9 is parallel to the Mids pot, Fuzzdog's C10 is before the pot??
The Colossus uses much larger values around the Mids pot than other Muffs with a Mids pot (Musket, Hoof; see Fuzzdog doc for those). Is there something wrong?
This is beyond me, I'm sorry.

Thank you!!!!

Here's what I came up with matching the Kit Rae diagram with the Fuzzdog diagram for use on the PCB (The parts numbers are for the PCB, Kit Rae has different numbers). I think I have it all except for the parts around the Mids knob parts mentioned above:

R1 33k
R2 100k
R3 470k
R4 140R
R5 12k
R7 1k
R8 10k
R9 100k
R10 470k
R11 12k
R12 390R
R13 10k
R14 390R
R15 470k
R16 100k
R17 12k
R18 47k ??
R19 10k ??
R21 100k
R22 470k
R23 2k
R24 10k
R25 1M
(no R6 and R20 on PCB)

C1 10nF + 100nF/2u2 on switch
C2 470pF
C3 100nF
C4 100nF
C5 560pF
C6 47nF
C7 100nF
C8 560pF
C9 47nF
C10 22nF ??
C11 47nF ??
C12 100nF
C13 100nF
C14 100uF

D1-2/4-5 1N4148
D3&6 by choice
D7 1N4001

Q1-4 2N5088

Tone / Mids / Sustain 100kB
Volume 100kA

10
Open Discussion / Re: New Boss/Sola Sound Pedal
« on: February 26, 2021, 03:01:03 AM »
LOL
It's 350 $

11
Open Discussion / Re: Let's make suggestions on the next Giveaway
« on: February 10, 2021, 03:21:05 AM »
Rump Roast or Bacon Bits reissues.

13
Build Reports / Re: Last of 2013: Behringer UV-300 rehouse
« on: January 05, 2021, 05:10:00 AM »
..just sharing how I did my Behringer rehouse..
That first picture is brilliant!

I finished mine in copper hammertone:


14
Build Reports / Re: Engineer’s Thumb
« on: December 14, 2020, 08:09:55 AM »
Hmmm... just checked out the JMK schematic and it uses the CA3080 instead of LM13700 that you have and it's only listing the two controls.
Will have to do some more checking up on what's floating around there, thanks for quick reply!

Isn't the inventor's schematic the proper official one?
http://www.valvewizard.co.uk/engineersthumb2.html

Here's another PCB with a schematic in the build doc:
https://shop.pedalparts.co.uk/Engineers_Thumb_Compressor/p847124_19924891.aspx

15
Open Discussion / Re: Your Preferred Pedal Amp
« on: November 19, 2020, 03:04:53 AM »
Blackheart Little Giant ... even managed to hold onto two 1x10 matching cabinets. Currently unmodified and I may well keep it that way. I don't particularly feel the need to carve this amp up to make it "better"
Mine too, it's a great amp.

Pages: [1] 2 3 ... 35