Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - artstomp

Pages: [1] 2 3 ... 12
Open Discussion / Re: A member is in distress and in need of good vibes
« on: August 09, 2019, 06:46:26 PM »
..get well Rej !!!

Open Discussion / Re: Your suggestions on overdrives for mbp
« on: June 04, 2019, 09:20:11 PM »
Pardon me but i know this is not an about a buffer pedal with a little eq control so i dont need to run to the amplifier to change its tonal control whenever i change guitars...

General Questions / Re: MXR EVH !
« on: May 10, 2019, 08:23:03 PM »
Thanks Scruffie...the flanger works on its own after readjusting the clock trimmer..( i leave it on that position ) as if nothing is is defective...when power is turned off, then turned on will no longer flange!...ill have to readjust the clock trimmer again to make it work again...yes itís hard to trace w/o schematic...
By the way, i already replaced some electrocaps...those 4 in horizontal position.

Note: as a i momentarily shorts the clock trimmerís pin 2 & 3 it works as it should...until the power is reset again..

General Questions / Re: MXR EVH !
« on: May 10, 2019, 05:54:39 AM »
Here's the gut shot Scruffie !....the vintage 117 flanger of course uses the SAD1024 BBD...

tnx for trying to help !

General Questions / MXR EVH !
« on: May 09, 2019, 04:24:20 AM »
Iím trying to repair an MXR EVH flanger for my sonís friend...when powered on, you can hear the LFO sweeping bypass mode the sweeping bleeds also. The BBD chip, MN3204 works fine ( i guess ) because as i turn the clock trimmer clockwise all the way, then turn counter clockwise, it is now flanging 100% as it audible changes heard when the bias trimmer is turned in any position.
    But as I reset the power...the flanging was gone, LFO again is heard sweeping loudly again....and when i repeat turning the clock trimmer as describe earlier...flanging now occurs normally.
   As the EVH boards is SMT, thereís not much i can replace. I swapped out an MN3207 as it has the same pin config but has a higher delay stages...just to test somehow if the MN3204 is defective in some way. But same scenario happens with the MN3207. ( tho it ďflangeĒ in a different way ).
   Any suggestions where should i look. Tnx in advance.

Build Reports / Re: Eoo3: Programmable Looper/Switcher/Midi Controller
« on: April 04, 2019, 04:06:44 PM »
I definitely will grab a set of the Eoo3 boards!...i noticed the 5v relays used are different from Linda.

Open Discussion / Re: Total Time Logged in
« on: March 26, 2019, 04:04:22 AM »
46 days, 13 hours and 32 minutes

General Questions / Need +12v, -12v on Road Rage
« on: January 30, 2019, 10:34:34 PM »
..Hi y'all....i understand that a 9v input on the road rage will render an 18v and -9v outputs. A 12v input will scale to 24v output, but will i get a -12v on pin 5 of the charge pump?

thanks i advance

Open Discussion / Re: DOD FX90 rev H schematic?
« on: January 10, 2019, 05:20:47 PM »
Hi lars...i've got 2 diff vintage is working the other has dry signal but no delay...they have different trannys and capacitors value...i think i might need the schematic...would you mind posting it here or you can send it to my
Thank you

General Questions / Presence gain on BDI21
« on: January 07, 2019, 08:51:25 PM »
Hi you all bass player friend has Behringer BDI2 and asking me he needed more on the presence knob and more lower end on over all tone...please advice which resistors/capacitors should be replaced...i know Behringer BDI21 is a copy of the SANSAMP Bass here is the schematic of the latter...thank upu guys in advance...

Build Reports / Re: Programmable Arduino Looper / Switcher
« on: November 04, 2018, 12:08:55 AM »
I would incorporate the write in each program button. Hold a program button down and the preset is stored on that button in the current bank.

The buttons are not aligned intentionally. I find the back row easier to access that way...

...yes..having the WRITE on each program buttons is way cooler and appropriate...
..i just wish you find plenty of time for the doing the upgraded version...

Build Reports / Re: Programmable Arduino Looper / Switcher
« on: November 03, 2018, 09:24:20 PM » the same board from a trade 3 years ago from you...haven't finished it yet...but the only things i'm missing are the relays and power supply...
..if i may suggest considering you are planning to reprogam it possible to incorporate the WRITE sw with the BANK sw?...holding the BANK sw for 3 seconds or function as a WRITE sw...the reason for this is just to have 8 foot switches instead of 9 (on the first row) thus the 2 rows (presets and loops) are alligned vertically...

Global Annoucements / Re: Projects Page update
« on: October 31, 2018, 08:47:52 AM »
Should I have another button to view just the pdf docs, too? Is that convenient instead of having to d/l the zip with the doc and drill file, then unzip before you even see the doc?

This I prefer..

Open Discussion / Julia Lag control
« on: July 13, 2018, 03:25:33 AM »
..hi did Walrus Audio Julia do the LAG control on this chorus this based on a MN3007 bbd chip?...tnx

Global Annoucements / Re: health vs. mbp
« on: May 28, 2018, 08:40:53 AM »
Get well mr Bean !

Pages: [1] 2 3 ... 12