Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ggarms

Pages: 1 ... 19 20 [21]
301
Tech Help - Projects Page / Re: Oh no sdx
« on: September 27, 2013, 05:46:05 PM »
or is this supposed to happen?

302
Tech Help - Projects Page / Re: Oh no sdx
« on: September 27, 2013, 05:45:24 PM »
Well, I checked the IC's-- Pin 5 of the 62 is rapidly fluctuating between 3 and 5 or so volts. Any thoughts? I swapped it out, and it did the same thing with another one

303
Tech Help - Projects Page / Re: Oh no sdx
« on: September 27, 2013, 09:35:59 AM »
Makes sense. Next step audio probe. My thought is to set the repeats at max and find where in the circuit I stop getting oscillation. Hopefully this will lead me to the buggy component. Could my 62 or 72 be bad? Would that cause the repeats to stop?

304
Tech Help - Projects Page / Re: Oh no sdx
« on: September 27, 2013, 07:42:10 AM »
So I de and resoldered the pot. While it was unattached I checked resistance-50k. As soon as I attached it that number went back down to 9k.

305
Tech Help - Projects Page / Oh no sdx
« on: September 26, 2013, 06:53:51 PM »
So life was great until this afternoon. I was playing the sdx this afternoon, currently unboxed. I pushed the repeats pot upward just a tad, and now I am only getting slapback, even when maxed. SO FRUSTRATED. I'm not sure if something else got bumped in the process. I took a voltage reading across the repeats pot and I'm only getting about 9k when maxed. The slam button also doesn't work. I tested both pt's in my rebote. They are fine. Any specific components I should be looking at to start? I'm not great with complicated schematic troubleshooting yet...  If you can offer any wisdom , oh pedal gods, please. I am in need and the next stop is my garbage disposal.

306
Tech Help - Projects Page / Zeropoint SDX
« on: September 26, 2013, 10:23:23 AM »
Hey guys, I read the tech help suggestions, so I am updating my prior post. I'm new 'round these parts, so forgive the prior post.


 I have verified that I have no cold joints, and no unwated bridges. I have tried adjusting the speed in all filter modes and with mods on and off. as soon as I get past 8 oclock or so on the delay speed, I get modulation/crashing noises with some popping. When the delay pot is any lower than that, everything functions as normal. I've only substituted 2 part values- one 18k resistor in place of one of the two 20k resistors. I'm not sure what steps I should take next to diagnose/ fix the issue, because I don't know what would cause everything to work normally until the delay time is sped up. halp plz? Any suggestions would be greatly appreciated.

307
Honestly, i'm loving this thing. I am having one problem. When i'm past 9 or so on the delay pot (quick repeats), the entire pedal goes wacky- almost like mod is turned on and cranked and slam is being pressed on and off. As soon as I back it down to a bit slower repeats it is fine, but not having 25% of the delay range doesn't sit right with me. any suggestions? Thanks!

308
Tech Help - Projects Page / ZPSDX
« on: September 23, 2013, 06:55:52 PM »
Hey Guys,


Im finishing up the sdx and i have a question. I only have one on/on SPDT. I have a few on/off/on SPDT's that would fit. IS this an ok subsitution? Thanks!

Pages: 1 ... 19 20 [21]