Messages

A ludwig phase II pcb.... a Korg Phase-wah pcb... a Frostwave funk-a-duck pcb...

Oh my.

PLL, Ludwig, MrMulti and Frostwave pcbs are all up for sale on the site now

Any chance you have an ETA on the String Ringer PCBs? It'd be great to be able to get a couple of things in the same order if possible.

Edit: just noticed the PLL boards sold out already...dang. Welp, guess I'll be waiting either way then.

Both PLL and ring stinger will be back in stock in a week or so

Sent from my F5321 using Tapatalk

A ludwig phase II pcb.... a Korg Phase-wah pcb... a Frostwave funk-a-duck pcb...

Oh my.

PLL, Ludwig, MrMulti and Frostwave pcbs are all up for sale on the site now

I got one of the Mr multis from the pusherman sale as well as a few others. Any chance you have the build doc?

BTW. Real high quality pcbs.

Hey, I did post in pusherman at the beginning of the week.  I'll get something uploaded today, sorry for the delay

Sent from my F5321 using Tapatalk

A ludwig phase II pcb.... a Korg Phase-wah pcb... a Frostwave funk-a-duck pcb...

Oh my.

PLL, Ludwig, MrMulti and Frostwave pcbs are all up for sale on the site now

Build progress

Damn that looks so clean! Between this and your Ring Stinger PCB i really can't wait to send you all my money    Please do let us know when you do a run of them, i'd be gutted to miss out

Now with knobs

Sent from my F5321 using Tapatalk

Last update,

This spent a week on the bench and wouldn't pass signal, finally figured it out and it runs pretty sweet, still need to find some time when the nipper is out of the house to really give it a blast.

Sent from my F5321 using Tapatalk

So things went a bit quiet on this one, sorry.
The original build works great but the 9mm pot combo with the large rotary switches as a no go, plus all the controls were mega cramped.
So I rejigged it with 16mm pots in a larger layout, ordered the boards and sat around waiting.

The delivery went missing in the post but finally arrived yesterday.

As always I'm short of a few components but I think it's much better in a larger enclosure.

Sent from my F5321 using Tapatalk

Build progress

Damn that looks so clean! Between this and your Ring Stinger PCB i really can't wait to send you all my money    Please do let us know when you do a run of them, i'd be gutted to miss out

Now with knobs

Sent from my F5321 using Tapatalk

Last update,

This spent a week on the bench and wouldn't pass signal, finally figured it out and it runs pretty sweet, still need to find some time when the nipper is out of the house to really give it a blast.

Sent from my F5321 using Tapatalk

Build progress

Damn that looks so clean! Between this and your Ring Stinger PCB i really can't wait to send you all my money    Please do let us know when you do a run of them, i'd be gutted to miss out

Now with knobs

Sent from my F5321 using Tapatalk

Build progress

Yes and yes.  The PLL splits the ac power though the two regulators which are adjusted via the two trimmers, you should be looking for +11V and - 11V there or there abouts depending on the iCs you are using.  Have a look through the thread over on DIY for a clearer idea of how to set it up.

Boards have arrived, waiting for parts

Sent from my F5321 using Tapatalk

V decry hmm 0 0000000 cc

Sent from my F5321 using Tapatalk

Yeah, I had trouble routing it with the divider below the multipler, too many crossed traces with the pots and ICs.  This isn't as faithful to the original but given the drone and momentary footswitches and all the off board stuff are all on board I think most people won't mind.

Sent from my F5321 using Tapatalk

A little update, just waiting for payday


Sent from my F5321 using Tapatalk

I've managed to rework it so that I can fit a 16mm pot on-board for the response control.  it's not ideal, but it will do the job.  I just need to get the stomp switches spaced correctly and do a final check over, then I think I can get a set of prototypes made.  Keep your eyes peeled for updates.

I've hit a bit of a snag with the design I made.  I cannot find a B2M 9mm right angled pot for the response control.  I get the impression they don't exist. 

Anyone got any ideas where to find one? otherwise it's back to the drawing board.