Yes, how soon I forget even the basics. You're the best alanp!
Help me teach myself.
-M
Typo'd from my iphone
Help me teach myself.
-M
Typo'd from my iphone
- Welcome to madbeanpedals::forum.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
#47
Open Discussion / Re: what are you guys listening to at the moment?
October 27, 2018, 06:20:58 AM #48
Open Discussion / Any experience/caveats with Ali-Baba
October 27, 2018, 06:11:56 AM
Sorry took so long to reply I've just finished digging through every last pot that I have and I swear I have everything but. However I can order those without a problem.
I am bollicks at reading schematics but I think these were the two relevant sections.
I am in absolute babe in the woods when it comes to doing anything it's not strictly run-of-the-mill. Would you mind walking me through it?
-Mike
Typo'd from my iphone
I am bollicks at reading schematics but I think these were the two relevant sections.
I am in absolute babe in the woods when it comes to doing anything it's not strictly run-of-the-mill. Would you mind walking me through it?
-Mike
Typo'd from my iphone
#49
Open Discussion / Re: Any experience/caveats with Ali-Baba
October 27, 2018, 05:32:21 AM
Thanks guys, I'm not used to having this much trouble sourcing parts. It's frustrating when you are up against a hard deadline.
-Mike
Typo'd from my iphone
-Mike
Typo'd from my iphone
#50
Open Discussion / Any experience/caveats with Ali-Baba
October 27, 2018, 03:47:35 AM
So, I still can't source the 2/2.5ka 16mm pots that I need. Am desperate and looking over at Ali-Baba.
Is this a bad idea or does anyone have some caveats?
-Mike
Is this a bad idea or does anyone have some caveats?
-Mike
#51
How Do I? Beginner's Paradise. / Re: Aion L5 Build progress and questions
October 25, 2018, 03:55:12 PM
Thank you so much, I really appreciate it. I though so, I just like to check with someone who knows a lot more than I do.
-M
-M
#52
How Do I? Beginner's Paradise. / Aion L5 Build progress and questions
October 25, 2018, 11:26:53 AM
Sorry another question.
For number of the caps it says film in the description but on the Mouser BOM it shows an MLCC.
It shouldn't matter if I use box film in place of the MLCC, correct?
Also, could I use LM741cn in place of LM741P?
-Mike
Typo'd from my iphone
For number of the caps it says film in the description but on the Mouser BOM it shows an MLCC.
It shouldn't matter if I use box film in place of the MLCC, correct?
Also, could I use LM741cn in place of LM741P?
-Mike
Typo'd from my iphone
#53
How Do I? Beginner's Paradise. / Re: Aion L5 Build progress and questions
October 25, 2018, 05:52:54 AM
All right everyone I'm at a standstill until I can trade for some parts.
-M
Typo'd from my iphone
#54
Open Discussion / Re: Just Saying -- the soapbox thread
October 25, 2018, 01:20:52 AM
Did I leave my lube out again?
-Mike
-Mike
#55
How Do I? Beginner's Paradise. / Re: Aion L5 Build progress and questions
October 25, 2018, 12:17:23 AM
Solder then snip as you go.
A little clean up w/flux remover.
That's where I'm at so far.
-Mike
Typo'd from my iphone
#56
How Do I? Beginner's Paradise. / Re: Aion L5 Build progress and questions
October 25, 2018, 12:15:09 AM
Partially populated w/resistors
Covered w/tape to protect resistors from blu tack.
Covered w/blue tack. Press down firmly.
As you can see, it's pretty straight.
Typo'd from my iphone
#57
How Do I? Beginner's Paradise. / Re: Aion L5 Build progress and questions
October 24, 2018, 06:38:22 AM
Ha!
I've got paint pens!
Will you taunt me a second time?
-Mike
Typo'd from my iphone
I've got paint pens!
Will you taunt me a second time?
-Mike
Typo'd from my iphone
#58
How Do I? Beginner's Paradise. / Re: Aion L5 Build progress and questions
October 24, 2018, 06:10:03 AM
Thx Alanp,
I am most uncomfortable with deviation in this setting. However, I trust you guys. Now I'm just got to decide if I want to use it from an aesthetic point of view.
I'll soldier on with the build and let my subconscious chew on it for awhile.
-Mike
Typo'd from my iphone
I am most uncomfortable with deviation in this setting. However, I trust you guys. Now I'm just got to decide if I want to use it from an aesthetic point of view.
I'll soldier on with the build and let my subconscious chew on it for awhile.
-Mike
Typo'd from my iphone
#59
How Do I? Beginner's Paradise. / Aion L5 Build progress and questions
October 24, 2018, 05:45:41 AM
Thx Somnif,
HHMM showed 4.84M
I'm bollicks at reading schematics, but I'm trying to see what part of the circuit this in.
Any reason not to use the carbon fil resistor besides looks?
It looks to be on the front end of the input.
-Mike
Typo'd from my iphone
HHMM showed 4.84M
I'm bollicks at reading schematics, but I'm trying to see what part of the circuit this in.
Any reason not to use the carbon fil resistor besides looks?
It looks to be on the front end of the input.
-Mike
Typo'd from my iphone
#60
How Do I? Beginner's Paradise. / Aion L5 Build progress and questions
October 24, 2018, 05:29:29 AM
OK so I decided I'm going to blog this build as I go.
I only made it to step three before I got stumped. Help me identify this part, I have it my resister box and it's labeled four. 7 AM it reads four. 7 AM on the multimeter I just need to know if it's a different wattage or is it just a different brand than I'm used to her usually use Xicon. I don't want to get done with this and find out that I messed it up in the very beginning
Any Ideas?
-Mike
Typo'd from my iphone
I only made it to step three before I got stumped. Help me identify this part, I have it my resister box and it's labeled four. 7 AM it reads four. 7 AM on the multimeter I just need to know if it's a different wattage or is it just a different brand than I'm used to her usually use Xicon. I don't want to get done with this and find out that I messed it up in the very beginning
Any Ideas?
-Mike
Typo'd from my iphone