Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - masterlk

Pages: 1 ... 10 11 [12]
166
Open Discussion / Re: How much is too much???
« on: November 18, 2010, 10:31:54 PM »
Nah you are not bored! This is just really interesting stuff! I'm a noob and I check out this site several times a day. I love the build reports too. I purchased my first two boards last month(Fatpants and Sunking) and I can't wait to get them done to show everyone. I have checked out the other sites as well, they all have really good info for the DIY'er. Not sure why I picked this site over others to be a part of, maybe because it seems smaller. One thing that I really, really dig is that when you need help there is always someone there to chime in. No jerks either, just really nice folks from what I can tell.

167
Tech Help - Projects Page / Re: Smallbear Pots
« on: November 14, 2010, 12:42:59 PM »
Ok, once again thanks!

168
Tech Help - Projects Page / Smallbear Pots
« on: November 14, 2010, 12:12:31 PM »
Hey guys - The pots I got from Smallbear have a little tab on the right side which prevents it from laying flat in the enclosure. From all the build reports I've seen, I don't see that anyone is drilling a small hole to accommodate for this. Is everybody just clipping the tabs off? Thanks in advance.

For example Smallbear part number 1005A


169
Tech Help - Projects Page / Re: Fatpants Trim pot
« on: November 14, 2010, 11:44:02 AM »
Makes sense. Thanks!

170
Tech Help - Projects Page / Fatpants Trim pot
« on: November 13, 2010, 11:34:45 PM »
I noticed that the trim pot I got from Samllbear(part number 1015) has the pin outs reversed from what the Fatpants board will accept. So, 3 is going to 1 and  1 to 3 and 2 is the same. This won't work, or will it? If not, I included a link for the part I bought(which doesn't show the pin arrangement) can anyone offer a replacement from anywhere if I need to swap it?

http://www.smallbearelec.com/Detail.bok?no=160

Thanks.


171
General Questions / Re: Transistor Sockets
« on: November 04, 2010, 01:33:15 PM »
Perfect, thanks guys.

172
General Questions / Re: Transistor Sockets
« on: November 04, 2010, 11:54:11 AM »
Oops! I mis-spoke. I meant the Fatpants. Total noob!

173
General Questions / Re: Univibe
« on: November 04, 2010, 11:29:11 AM »
I would love one of these! Anybody have one or have first hand experience with one? The clips I've heard are great.

http://www.krmusicalproducts.com/smallmegavibe.htm

174
General Questions / Re: Transistor Sockets
« on: November 04, 2010, 11:24:22 AM »
Good deal, thanks! I was wondering about the inline ones. I am going to build a Sunking and I'm fairly new at soldering and I didn't want to fry my transistor but those round ones don't match up with the holes on the Sunking board...so go with the inline? Are they low profile enough?

175
General Questions / Transistor Sockets
« on: November 04, 2010, 10:45:29 AM »
Hey what are you guys using for Transistor sockets? Part numbers from wherever would be great.

Thanks.

176
Build Reports / Sun King 1590B
« on: October 27, 2010, 09:23:44 AM »
Anybody get a Sunking in a 1590B with a battery?

177
Build Reports / Re: Sunking Triplets
« on: October 26, 2010, 08:43:22 PM »
Nice looking pedals - everything is better in 3's! :D

Pages: 1 ... 10 11 [12]