News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - lloyd17

#1
How Do I? Beginner's Paradise. / Re: Heatshrink
February 25, 2012, 12:45:36 AM
harbor freight is cheap for shrink tube
#2
Global Annoucements / Re: How is babby formed?
February 16, 2012, 04:07:49 AM
wonder if I can cram a fuzz face, p45 and urchin into a landscape 1590bb. definitely going to try!
#3
General Questions / Re: sourcing parts for DMM
February 15, 2012, 08:51:04 PM
Mouser has all that stuff
#4
General Questions / Re: Another Supplier.
February 11, 2012, 10:48:35 PM
thanks for the heads up, just placed my second order after the test order went perfectly. great place for I/o jacks, al knobs and ge diodes!
#5
Requests / Re: Helicopter/stuttering tremolo
February 11, 2012, 10:23:22 PM
trem lune does stutter, sine, up/down ramp etc. easy and super versatile.
#6
Open Discussion / Re: My 3PDT Wiring Boards
February 09, 2012, 07:06:41 AM
that's slick, nice work!
#7
General Questions / Re: double delay layouts
February 02, 2012, 04:23:04 AM
No boards, just layouts on their fake 3005 page
#8
I have trouble getting components out of double sided boards with any solder type lol. RE the pot legs I'd just cut t hem at the angle leaving enough to grab the pin with hemostats (my tool of choice for these tasks) and enough terminal on the pot for later recycling. I never try to remove solder until after the component leg is out. Actually I add solder when pulling components to ensure the whole joint gets gooey, then remove the lead, then clean up the hole.
#9
I find it easier to cut off the pins before removing pots. rather lose a couple bucks in parts than the whole board. plus the pots can be used again lug style.
#10
General Questions / double delay layouts
January 31, 2012, 08:31:16 AM
well I'm sick of getting hosed on 3005 chips so its time for the 4x3008 hack on my dirtbag. Trouble is smallbear has a double sided layout. Anyone know of a single sided layout or even better a vero? Figured I'd ask before trying my own. Thanks!
#11
Open Discussion / Re: Where to source short electros
January 30, 2012, 09:22:13 PM
Mouser is where I get mine. There is a size field in their parts finder. Here are the 10uf and 100uf I use to keep my road rage boards tiny, should be a good starting point.

http://www.mouser.com/ProductDetail/Lelon/SS101M1EBK-0805P/?qs=4Fsi%252bhdDJ3NcrmmftcC5ow%3d%3d

http://www.mouser.com/ProductDetail/Nichicon/USW1E100MDD/?qs=UBiR96IgLrQJYVP6qc6V0g%3d%3d
#12
General Questions / Re: voltage inverter layout
January 28, 2012, 10:22:43 PM
There's a layout on the sabrotone site. Harald has some cool projects over there.
#13
Build Reports / Re: Stage Fright
January 27, 2012, 04:24:01 AM
Hell I'd wig right out if I could get a PCB just for that molten voltage chip.
#14
Open Discussion / Re: Best DIY compressor?
January 26, 2012, 09:06:25 PM
Yea I am planning a comp using Barrys morc with added clean blend for a tone press workalike. Maybe squeeze in one of the coldcraft minibax boards I have kicking around as well. I gotta figure out how to use up all of these PCB's haha.
#15
Open Discussion / Re: Cabling these puppies
January 26, 2012, 06:21:00 PM
Wow we do all buy our bulk cable the same way. Oc speaker for angle jacks and ebay for lava mini. For long leads I also use redco but i really like the gepco xband stuff for the way it lays and coils.