Topics

[http://www.firstgiving.com/fundraiser/Hiwattbob/2012-cures-kids-conquer-cancer-one-day-at-a-time]

Hey folks, there's a raffle going on over at HCFX but it's open to everyone (just be sure to note the bottom paragraph). There's a ton of great prizes and it goes to a great cause, you can check it out here: http://www.firstgiving.com/fundraiser/Hiwattbob/2012-cures-kids-conquer-cancer-one-day-at-a-time

From the site:
OK Bros--we're making donations here on behalf of Phil O'Keefe's family.
Raffle
For every $10 donation, you'll recieve 1 raffle entry.
For every $20 donation, you'll recieve 3 raffle entries.
For every $30 donation, you'll recieve 5 raffle entries.
Deadline to contribute for raffle entry will be December 1st, 2012 at noon.  Raffle drawing will be done shortly after.
Prizes:
Haunting Mids v3 Fuzz (donated by Hiwatt Bob)
One-of-a-kind SuperRat titled the "Murinae"  (built and donated by Hotmess)
2 Wilson Effects (TBD) (donated by Wilson Effects)
BJFE Sea Blue EQ clone (built and donated by Cryptosonic)
EAD Pedal (built and donated by WeStartToDrift)
Red Panda Context reverb pedal (donated by RedPandaCurt)
Danelectro Black Licorice Octave Dist (new in box, donated by Aedes)
Used Boss Flanger BF-2 (donated by Macadood)
FreekishBlues Red Dot pedal (donated by FreekishBlues)
$25 Best Buy Gift Card (donated by Beaselyboy)
Other donations welcome.

Non HCFX contributions:
All donations are welcome, including non-HCFX forum members.  If you are not a member, either enter your email as your display name--or send an email with your display name in the subject line to:
philisdabes@hotmail.com
If you are a winner, you will be notified via the email address you provide.

Hey folks, I recently built the Cupcake compressor, I wired everything up off board because I'm impatient and it worked fine, then today upon getting a couple enclosures I boxed it up and it worked but it was a rats nest of wiring and upon tweaking the trimpot I subsequently wasn't getting any sound when bypassed or with the effect. I completely rewired it using a 3dpt board, much cleaner and tidier but now I'm still getting no sound when bypassed or with the effect on. The led on the board would no longer light up either after the switch, but the onboard 3dpt LED does. I'm hoping it's something simple, I've traced everything and it seems okay. I've uploaded pics here http://www.flickr.com/photos/mattgnarly/sets/72157629083298746/

Hey folks, I finished (I thought) populating and wiring up the Cupcake compressor and figured I'd try it out and am getting a super loud humming, sounds like it isn't grounded. It is not boxed up, which is what I'm assuming is the problem (still waiting on enclosures), so is there a way I should be grounding it for now?

Hey guys, so after buying a ton of parts and too many pcbs I'm finally getting around to putting together my first PCB, the Zombii. Everything went fine assembling the PCB but I'm a little confused as to the wiring. I'm using a 3pdt switch (for true bypass) and a 9v adapter (no battery). The wiring guides are down so I'm not too sure how to go about it.
Cheers

I've seen a lot of reverb requests, and share the sentiment, but I also think something like the EQD Dispatch Master would be pretty rad. I think it's basically a belton brick reverb/pt 2399 delay. Sounds great in the demo vids I've heard.

I'd be curious to see if anyone has any experience with the Walrus Audio Voyager or Iron Horse. I've only seen demos on youtube and no gutshots. From what I've heard the Ironhorse is Rat-based and the Voyager is Klon-based but not confirmed, so it'd be nice to build something similar instead of ordering and possibly not vibing with the Walrus pedals.
Cheers guys and gals

I've noticed that on a lot of vero schematics and the Madbean PDFs I've read, that often times the type of pot isn't specified. In general, is audio or linear taper the standard?
Thanks

I've read the pdf a couple times now and I'm still not entirely clear on this, can the Road Rage be used to power multiple effects?