News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - chordball

#1
Open Discussion / For bela1961
May 08, 2018, 10:54:13 AM
Hey man, I'm trying to send a message about some build docs but your inbox is full. Clear out some messages and send me a PM please. Thanks! :)
#2
Cool! Glad you got it worked out. I spent quite a long time on an analog delay myself so I know what you went through. It's usually the simplest mistakes that take the longest to catch.

Do you have a scope? If not, I can send you some info on how to calibrate the delay using a signal generator on your phone and a free scope program on your computer. At the very least, I'd use an audio probe to set the cancel trimmer, then listening to the full output adjust the delay time so that the whine just barely starts and then back off a tad to eliminate it.
#3
With the way the mix pot is set up you should be able to completely kill the wet signal. I'd check the pot to make sure that pin 1 is at ground, and that pin 2 goes to ground at full CCW.
#4
Build Reports / Re: CE1 CHORUS FINISHED
April 18, 2018, 02:23:09 AM
Sweet! Glad to see it finished.
#5
Open Discussion / Re: PTB or TBX help!
April 06, 2018, 11:13:07 PM
Quote from: claytushaywood on April 06, 2018, 03:14:42 PM
I thought you could still get all the standard strat tones as long as you dont use the bass cut?  seems like a pretty typical low pass filter on the 250k part. 

Anyone have any ideas on this?  Its hard to find the 1mC pot that the G&L PTB calls for... all I can find are the alphas i have stashed for pedal builds.  Maybe I'll just use one of those for the bass cut and one of the CTS mini pots for the treble cut- and do a 4 knob strat.

ahiddentableau was talking about the TBX, not PTB. I have been wanting to try the PTB system myself and couldn't find the pot except directly through G&L. I think I will buy from them but the price is pretty high.
#6
Build Reports / Re: BOSS CE1
March 16, 2018, 12:49:50 PM
Nice! I'm down for one when you get them sorted.
#7
General Questions / Re: Afterlife vs 4:1
January 25, 2018, 03:02:39 PM
Cool. Thanks a lot guys!
#8
General Questions / Re: Wah pots - recommendations?
January 23, 2018, 01:50:31 PM
My vote is for Joe Gagan's pot or the Mccon-o-pot. I prefer the taper of Joe's pot but the smoothness of the sealed Mccon-o-pot.
#9
General Questions / Re: Afterlife vs 4:1
January 23, 2018, 01:42:20 PM
Quote from: madbean on January 23, 2018, 04:01:43 AM
There's no real con to having a clean blend....it's simply an "additive" option that can be completely removed by turning the knob down. I guess I'd describe the "pro" as being able to create a more unique compression mix than you would have without a clean through. You can get a lot of compression pumping through without it feeling overdone (as is the case with many one knob compressors)...IOW added sustain without overly-compressed dynamics.

Thanks for the help Brian. I wasn't sure if/how the added circuitry would change the feel if the clean was dialed completely out. I'm leaning towards the 4:1.
#10
General Questions / Afterlife vs 4:1
January 23, 2018, 02:57:02 AM
I'm interested in building one of these two compressors but am undecided on which one. Can any of you offer some insight on the pros and cons of the clean blend option of the 4:1? Thanks!
#11
VFE Projects / Re: VFE site down
January 23, 2018, 02:53:19 AM
Man, I'm bummed I never paid up to get those eagle files!
#12
Build Reports / Re: ABDX-PIF build
January 08, 2018, 05:21:13 AM
Quote from: EBK on January 07, 2018, 05:05:10 PM
Thanks!

Through-hole NE570s are no longer in production, so the SMD version is far easier to procure, and I need to keep sharpening my SMD skills to be ready for the future.  ;) I don't actually have a solid reasoning other  than that (a Coolaudio v571d would have worked instead). No cost savings here, as the adapter board cost as much as the chip.  ;D

The vactrol came from Smallbear:
http://www.smallbear-electronics.mybigcommerce.com/photocoupler-coolaudio-vtl5c3/

Ah, thanks for that. I thought only xvive did a "real" VTL5C3. Interesting.

Looking forward to seeing your completed build. If I'm lucky maybe I'll get mine built before 2019!
#13
Build Reports / Re: ABDX-PIF build
January 07, 2018, 04:44:57 PM
Looking good! I dig that layout a lot. Any reason for an smd NE570 other than that it's probably what you already had?

Also, what vactrol is that? It's the same one that's used in the new micro-tron. I've been curious what it was but could never find it anywhere.
#14
General Questions / Re: Wah Circuit Question
December 20, 2017, 01:48:36 AM
Aesthetically speaking, my vote is for the weener. Man, that is something I never thought I'd say. :o
#15
Quote from: jubal81 on December 12, 2017, 07:37:22 PM
Quote from: chordball on December 12, 2017, 07:09:39 PM
Quote from: jubal81 on December 12, 2017, 05:04:59 PM
Seeing a couple points on this schematic that could possibly cause noise issues. Find it any noisier than other compressors?

Can you elaborate? Any ideas for improvements? I haven't built it but it was on my radar.

Mainly thinking about the LDR on the noninverting opamp input going to a reference voltage. Noninverting inputs have ridiculously high impedance, so that net is extremely sensitive to picking up noise. It's a good idea on layout to keep any traces connecting to a noninverting input absolutely as short as possible.

I've noticed that phasers that use a negative voltage for a split supply rail are much quieter than those with a single rail and reference voltage. If you look at the Mutron Phaser schematic, you see the noninverting inputs and corresponding LDRs are referenced to ground in the phase stages.

Thanks for the explanation. Definitely not something I even considered before so I learned something new. If/when I build this circuit I will play around with the supply scheme.