Yes. Use a sharpie marker to fill in the gaps around the edges. Do not worry about the paper. It is just extra protection from the solution. Even the second attempt could have been salvaged with some patience and a straight edge. The enclosures have a lot more mass than our copper boards and thus never get as hot.
- Welcome to madbeanpedals::forum.
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
#527
Open Discussion / Re: Tayda Right Angle Plugs
June 23, 2012, 01:15:05 AM
I have had a lot of headaches from that design. I swore off them in the 80s. TDPRI has good buzz about gfs right angles. But quite precious, but half of George L's
#528
Mods / Re: Grapevine rock/rawk switch wiring
June 16, 2012, 11:43:08 PM
Thanks,
I mean to remove the Rawk mode.
I mean to remove the Rawk mode.
#529
Mods / Re: Grapevine rock/rawk switch wiring
June 16, 2012, 06:21:36 PM
Should I post this in the tech help forum?
#530
Mods / Re: Grapevine rock/rawk switch wiring
June 14, 2012, 11:25:53 PM
If I exclude C6, C7, and C8, and R7 and R8, would I need a jumper on the switching pads to just exclude the switch altogether and have just the Rock mode. I do not care much for toggle switches.
#531
Open Discussion / Re: PPP Penny Vein enclosure - knob suggestions
June 14, 2012, 11:01:02 PM
I was thinking cream, but the black is quite pimp.
#532
Mods / Grapevine rock/rawk switch wiring
June 13, 2012, 07:02:33 PM
I am finally building my grapevine I purchased 18 mos ago.
I want to wire the rock/rawk switch 3pdt switch and I am not skilled enough to lay it out.
I have read posts from other members about this, but I have searched and cannot find a wiring diagram for the footswitch.
Can anyone please show me how to wire the switch?
thanks. I hate to ask for stuff, but I am trying to do this the correct way.
I want to wire the rock/rawk switch 3pdt switch and I am not skilled enough to lay it out.
I have read posts from other members about this, but I have searched and cannot find a wiring diagram for the footswitch.
Can anyone please show me how to wire the switch?
thanks. I hate to ask for stuff, but I am trying to do this the correct way.
#533
Open Discussion / Re: Is there an auto wah that just sweeps in a fixed cycle?
June 04, 2012, 10:50:21 PMQuote from: culturejam on June 04, 2012, 02:36:56 AM
I worked by B. Tremblay from RunoffGroove on a project we called the Quinoa (pronounced Keen-wah). It's an inductor-based wah circuit with an LFO.
It ended up sounding pretty cool, even though neither of us ended up doing anything with it. And I really need to update the PCB layout.
CJ, could you explain switches1 and 2. I am very interested, but is it like the phozer or more of a wah?
#534
Open Discussion / Re: preamp porn
June 04, 2012, 12:05:53 AM
I wish we could source those Portico knobs. 
Those preamps make realize how software dependent I have become. I do not use my rack recording gear anymore. I am remembering it sounded pretty nice. I need more time to see if my memory is accurate this week.
Those preamps make realize how software dependent I have become. I do not use my rack recording gear anymore. I am remembering it sounded pretty nice. I need more time to see if my memory is accurate this week.
#535
Open Discussion / Re: Boost and Ts808 suggestions
June 04, 2012, 12:01:02 AM
http://img.photobucket.com/albums/v165/rickydon/Two_in_1_wiring.gif
The old ggg 2 in 1 wiring layout.
The old ggg 2 in 1 wiring layout.
#536
Open Discussion / Re: First Names - we all got em.
June 03, 2012, 11:57:22 PM
my name is charles. or chuck if we are buddies. Everyone should presume we are, because we are.