• Welcome to madbeanpedals::forum.

News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - jimilee

#2656
Build Reports / Re: Soulfull Drive
August 17, 2020, 01:20:48 PM



Sent from my iPhone using Tapatalk
#2657
Open Discussion / Looking for a Yorkshire Puppy
August 16, 2020, 10:16:12 PM
I can't seem to find one in a 150 miles radius of Chattanooga. Are they being discontinued???


Sent from my iPhone using Tapatalk
#2658
General Questions / Re: EHX Q-tron
August 16, 2020, 10:15:04 PM
Quote from: benny_profane on August 16, 2020, 09:56:41 PM
Check out the VFE Mini Mu if you haven't already.
This, just built one, nice.


Sent from my iPhone using Tapatalk
#2659
Build Reports / Re: Glitchee
August 14, 2020, 10:04:14 PM
Nice. I've started mine, got all the resistors in it, that's about it.


Sent from my iPhone using Tapatalk
#2660
Quote from: Bio77 on August 14, 2020, 04:57:17 PM
Glad it worked! 8)

Do you have a multimeter?  If so, check the voltage at the purple wire going to the LED.  I don't know this circuit, but I'm guessing the resister closest to the purple wire is the CLR for the LED.  It looks kind of suspicious (maybe a cold joint). Also, if you have a multimeter it might have a diode setting that you can use to check your LED.  I've only ever blown an LED by shorting it with no resister, so, I'd be surprised if it was fried. That will also tell you if the orientation is correct, as Jimi suggested.
I've blown more than I care to admit.



Sent from my iPhone using Tapatalk
#2661
Quote from: rpark71 on August 14, 2020, 02:44:20 PM
Just to update on last reply - switching the wires on the input jack worked! LED doesn't light, so not sure if blown but that's an easy swap for new one to see if it solves that problem. Thanks again for steering me in the right direction Bio77!

thanks, Rich
It may just be backwards.


Sent from my iPhone using Tapatalk
#2662
Those are sharp inside and out.


Sent from my iPhone using Tapatalk
#2663
It's in rotation in my car.


Sent from my iPhone using Tapatalk
#2664
Quote from: Matmosphere on August 12, 2020, 04:58:57 PM
Score! Found an open box one at 2am last night 10% off
Nice. Many deals have been done at the witching hour. Not all of them good or done sober.


Sent from my iPhone using Tapatalk
#2665
Quote from: Matmosphere on August 12, 2020, 04:58:57 PM
Score! Found an open box one at 2am last night 10% off
Nice. Many deals have been done at the witching hour. Not all of them good or done sober.


Sent from my iPhone using Tapatalk
#2666
Build Reports / Re: Flabulanche and boost
August 11, 2020, 04:04:00 PM
Daaaaamn, that's sharp. Well done.


Sent from my iPhone using Tapatalk
#2667
Open Discussion / Re: Mn3005 delay Mods
August 10, 2020, 06:22:30 PM
Quote from: thesmokingman on August 10, 2020, 05:23:16 PM
I believe the man-o-war also uses the 3101 (two of them, in fact)
Yep.


Sent from my iPhone using Tapatalk
#2668
Open Discussion / Re: Mn3005 delay Mods
August 10, 2020, 01:23:54 PM
I was curious for the ManOWar delay.


Sent from my iPhone using Tapatalk
#2669
Build Reports / Re: Lectric fx Clone Theory
August 09, 2020, 08:31:27 PM
Mystique, nice. That looks sharp man.


Sent from my iPhone using Tapatalk
#2670
Build Reports / Re: Man O War
August 09, 2020, 08:21:57 PM
Quote from: Thewintersoldier on August 09, 2020, 07:40:50 PM
Nice, is that a tone vent up top?

Sent from my moto z4 using Tapatalk
Yep adds highs.


Sent from my iPhone using Tapatalk