• Welcome to madbeanpedals::forum.

News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - jimilee

#3211
Open Discussion / Re: Synth cube sale
February 23, 2020, 05:05:06 AM
You're welcome guys. I've had great success with these guys. Fast shipping also.


Sent from my iPhone using Tapatalk
#3212
Open Discussion / Re: Synth cube sale
February 23, 2020, 12:17:41 AM
Quote from: Aentons on February 22, 2020, 11:35:07 PM
I get  "Warning: Coupon is either invalid, expired or reached its usage limit!"
Did you create an account and login?
#3213
Tech Help - Projects Page / Re: Cavedweller2 noise
February 22, 2020, 10:17:43 PM
I think maybe clear up-close pictures of both sides of the board along with voltages on your pt2399s. If you can record a small bit of what you're talking about, that may help. Reflow all of your solder joints and make sure all of your values and polarities are right.
#3214
Open Discussion / Synth cube sale
February 22, 2020, 02:26:57 PM
This is where I got some of my mn3005 chips. You have to create an account and use code code 21OFF at check out. I think they have clock chips too.


Sent from my iPhone using Tapatalk
#3215
Open Discussion / Synth cube sale
February 22, 2020, 02:26:26 PM
This is where I got some of my mn3005 chips. You have to create an account and use code code 21OFF at check out. I think they have clock chips too.


Sent from my iPhone using Tapatalk
#3216
Reflow all your solder joints, make sure all of your values are correct. Audio probe the circuit to see where it gets muddy. Hope this helps.


Sent from my iPhone using Tapatalk
#3217
Quote from: BrianS on February 22, 2020, 12:35:04 AM
Quote from: jimilee on February 21, 2020, 10:14:03 PM
Quote from: BrianS on February 21, 2020, 10:07:16 PM
I know you been doing your faceplates for a while but I never get tired of admiring them because they look so freaking good.  Wish I had a 32nd of your skills there.
When the purge happens, maybe some will have the faceplate. I got lucky on the last one.

I would be extremely honored to display one on my board.  Even if I couldn't get the pedal to work, LOL (which now days is more common than not).
It happens in cycles I've found.


Sent from my iPhone using Tapatalk
#3218
Quote from: BrianS on February 21, 2020, 10:07:16 PM
I know you been doing your faceplates for a while but I never get tired of admiring them because they look so freaking good.  Wish I had a 32nd of your skills there.
When the purge happens, maybe some will have the faceplate. I got lucky on the last one.
#3219
Build Reports / Re: A place for my stuff.
February 21, 2020, 07:42:31 PM
Looking good as always. Do you play your guitar through the defraculator or does it just make noise?
#3220
Daaamn, what did you drag it behind?
#3221
I wonder where a board for said phaser could be picked up...
#3222
Damn fine builds Dan, especially that phaser.
#3223
Build Reports / Re: Fat Driver
February 19, 2020, 01:35:45 AM
That is very sharp looking man.


Sent from my iPhone using Tapatalk
#3224
Open Discussion / Re: the pedal movie trailer
February 18, 2020, 10:40:21 PM
Quote from: cooder on February 18, 2020, 09:53:12 PM
Quote from: jimilee on February 18, 2020, 09:49:25 PM
Wow, that looks very cool.


Sent from my iPhone using Tapatalk
... there will be probably also a phaser or two in it. Giddy up! 8)
Now you're talking.


Sent from my iPhone using Tapatalk
#3225
Open Discussion / the pedal movie trailer
February 18, 2020, 09:49:25 PM
Wow, that looks very cool.


Sent from my iPhone using Tapatalk