Messages

What's the problem? IC10 Pin 7 is pulled to voltage via R45 & IC7 pin 4 is connected to it, comparators & CMOS go high and low...

Is it not working?

They're supposed to be like 16mv. I'm having troubled getting the mn 3007 biased. The signal is hot. IC 10 and 7 were the only anomalies I could find.


Sent from my iPhone using Tapatalk

IC10 Pins 2 and 7 and IC7 pin 4 have around 14v each and I don't know why. I have reflowed, scratched between joints on the bottom to make sure that there are no solder bridges and tediously looked at each resistor and made sure I had the right ones. Each cap and trannie are all correct. I even replaced those two ICs. I'm not sure where to go from here. Is something not dumping to the ground that should be?

Those look fantastic. I'm a sucker for flashing and pulsing LEDs. Welcome to the forum!

As far as the contest, it's one per category.


Sent from my iPhone using Tapatalk

Upgrading the site to https has broken the old youTube plugin so I have installed a different one. It works nearly the same except for the following:
You need to specify a display width otherwise it will show up native which is like 1200px or wider.

To embed youTube do the following:


1) Click on the first icon in the highlighted area shown in the image below. This will produce the following code:
(youtube)(/youtube)
it'll be in hard brackets but I've changed it to show what the test is.

2) Paste the unique identifier of the video. For example, ***https://www.youtube.com/watch?v=dQw4w9WgXcQ is a popular video. dQw4w9WgXcQ is the unique identifier. So, our code would be:
(youtube)dQw4w9WgXcQ(/youtube)

3) Last, you need to specify the width of display. I recommend 640.
(youtube width=640)dQw4w9WgXcQ(/youtube)

Here's what that would look like as an embed:
[youtube width=640]dQw4w9WgXcQ[/youtube]

PS If you rick roll I will instaban you for 5 minutes.

If you select the far right icon in the image below, you can display all the videos in a users channel. Example:
[yt_user width=640]madbeanpedals[/yt_user]


The new icons:

Bwahahahaha you can't stop me!!!


Sent from my iPhone using Tapatalk

Oh, man. The Florist chorus is sounding like a whole lot of alright. I can't wait for you guys to hear it. I'm going to have to work on some new demo videos.

I can't ...just....where's the bathroom, I can hardly contain myself....


Sent from my iPhone using Tapatalk

Even on my tiny little printer, I can fit 8 of these on the build plate. 

Boom, looks good.


Sent from my iPhone using Tapatalk

2uf total will be ok, it's not enough to make a difference.


Sent from my iPhone using Tapatalk

I'm sorry, I'm parallel. My bad.


Sent from my iPhone using Tapatalk

Working here.


Sent from my iPhone using Tapatalk

2-1ufs will work. That's what's on mine.


Sent from my iPhone using Tapatalk

That's pretty awesome man.


Sent from my iPhone using Tapatalk

That thing is off the proverbial chain!


Sent from my iPhone using Tapatalk

I'm waiting on that polyphase. Can't wait for February. Winter in Detroit is my time to build, to cold for anything else haha

February should be pretty off the hook. It's going to be phaser city up in here, and some of them will have tap tempo/waveform options.

Did someone say phaser?!


Sent from my iPhone using Tapatalk

Damn nice!


Sent from my iPhone using Tapatalk

Very cool. I was just thinking I need to build a new opticomp. I either sold mine or lost it.