• Welcome to madbeanpedals::forum.

News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - jimilee

#6091
Tech Help - Projects Page / Kwawk wah mod question.
July 12, 2014, 06:35:19 PM
According to R.G. Keen's article, if I put a 1k trimmer in place of the 470r coming off of Q1 (2n5088) to ground, I can reduce low end Oscillation. How would I wire the trimmer, 1 and 3 on the ground side, or 1 and 2 with the ground either not connected or hooked to a ground source?
#6092
Very nice, are you a lefty?
#6093
#6094
Paramix over at gpcb will do the same? It has an effects loop and a blend,  not really a blend so much but you can adjust the clean signal and the wet signal volumes separately.so you still get clean signal and effect signal.
#6095
Open Discussion / Re: Kwawk wah
July 11, 2014, 11:09:55 PM
I used a 2n5088 and a bc549 I got a lot of squealing with 2 2n5088. Sounds pretty good now, unless I add the extra caps, then it squeals again.
#6096
Build Reports / Re: Mr. Bubble Reverb (Rub A Dub)
July 11, 2014, 09:21:51 PM
I don't know I just put pin one in the square hole :-)
#6097
Build Reports / Re: Doubel Ganger - build thread
July 11, 2014, 08:33:47 PM
Nice ideas so far.
#6098
Build Reports / Re: Mr. Bubble Reverb (Rub A Dub)
July 11, 2014, 08:32:00 PM
That very cool. I put my brick underneath, but everyone else seems to put it on top. Interesting.
#6099
Open Discussion / Re: Great Googley Moogley
July 11, 2014, 03:58:12 PM
Only 6 mos to make? That's pretty quick for something like that. I suppose it just stays at home, that'd be a bitch to take anywhere.
#6100
I haven't been to the GGG site in a while, he has a lot more  projects now.
#6101
Build Reports / Re: Crvnchy
July 11, 2014, 03:17:33 PM
Wow, that's badassery right there.
#6102
Build Reports / Re: Kwawk wah.
July 11, 2014, 03:41:16 AM

Quote from: Leevibe on July 11, 2014, 03:16:42 AM
Right on. Relic'd!!
Hell yeah!!! Bought it that way...relic'd
#6103
Build Reports / Kwawk wah. Now with audio and mods
July 11, 2014, 03:09:41 AM
This is your basic wizard wah built on the grind customs kwawk wah board.. Sounds like the wizard wah. It has a terrible torrid inductor and a hot potz from Joe Gagan. UPDATE I removed the wah trimmer and 22k resistor, removed r6 470r and replaced it with a 1k trimmer, tuned out the rest of the oscillation. It's now a very usable wah.
[soundcloud]https://soundcloud.com/jimi-lee-2/kwawk-wah[/soundcloud]
#6104
Build Reports / Re: Dreamverb NSFW
July 11, 2014, 03:08:26 AM

Quote from: slimtriggers on July 10, 2014, 06:46:20 PM
I like how you matched the font color to the graphic.  Nice attention to detail 8)
Thanks, I actually sampled the colors in the graphic when doing the fonts. I wish I could match the knobs to the color also, but I don't like different colors knobs. I went with green knobs after this was posted.
#6105
Build Reports / Re: Dreamverb NSFW
July 10, 2014, 06:26:35 PM

Quote from: alanp on July 10, 2014, 04:41:09 PM
Nice, the Tenebrion is my favourite reverb :D

Where is the art from?
Somebody posted it on my timeline on Facebook ages ago. Any time I come across a cool image anywhere, I save it. I've had this one for sometime now.