Messages

Right on! That looks like a good pairing. Is it a 2x12, 4x10, or 4x12? I have an old Marshall 2x12 that looks a lot like that size.

4x12

Nicely done Jimi, similar to my Tweaker rig, only I'm running it into a 2X12 sealed cab.

Soon you will all but have forgotten there's a string gauge past 0.054........

I was looking for a 1x12 or 2x12 when I found this for 130. And srjeres a gauge past .054?

Nice setup!  Good luck to your neighbors...

They already know I'm a bass player 

So this is my new amp. Got it from mike Ballard a little bit ago and then today scored these shall cab for 130. Works great for raging in my music room.

Jimi: The pinout of the MPF102 is identical to the J201.

My misake, I was working with a j201 an mpf102 and nte458 Got them confused here.

Naa, go from the board to the output jack and then another wire from output jack to sw5. It will be easier because the output jack has more room for 2 wires. And the same for volume 2 to sw6. The lugs on the pot are big enough for 2 wires as well. This should make for neater wiring as opposed to running 2 wires off of the vero board.

Dude, Thank You!!!!!
What about the Sw4 part, just take the two wires and put them on the switch?

yes

Dem knobs!!!

Naa, go from the board to the output jack and then another wire from output jack to sw5. It will be easier because the output jack has more room for 2 wires. And the same for volume 2 to sw6. The lugs on the pot are big enough for 2 wires as well. This should make for neater wiring as opposed to running 2 wires off of the vero board.

today I had a problem with two pedals.

Wolfshirt + Univibe.

same vibe off the effect of this on the bottom.

used 3PDT and I made several calls en failed.
after several attempts I gave a look at some filter pedals. and decided to put 100ohms in early 9v pedal. solved!

gets the hint

That's what ever you just said for ya! I'm glad it worked out though. Gives you a great feeling when you debug successfully.

Just built 2 gorm shelf boards myself. There are some great YouTube videos that will give you some great ideas. Mine is just for kicking around the house too, although one day is like to play rhythm guitar in a band!

Rej has a great one, cave dweller sounds fantastic. All of the zero points are wonderful, and the multiplex is good too. I have built bunches

Pin out is different, and it depends on the application but recently I used a j201 in place of an mpf102 beacis has a great Pinout guide for most trannies made up until a few years ago. It's a good starting place.

I just use a pocket knife,must about anything works, but the dmm part is most important to make sure the cut is clean.

jimilee, I have been loving seeing your build efforts and your skills grow, this looks awesome!

Thank you all. I am very codependent and your encouraging remarks make me feel all warm and fuzzy!

Wait for Jon's blue warbler 2!!

That's funny! But actually I need this to be playable this weekend.

Trem or Vibe, QuattroVibe would fit that spot nicely.

I wish I had a good Vibe on hand, perhaps I can get one going this evening...

Uhhh...phaser duh!

Tremolo o o o o o o o

Those tend to be my go to options, and I have one of each, but I'm actually thinking of something else here.

Perhaps I was too restrictive in my limitations. I was thinking that maybe I didn't want to go with a Drive or Fuzz, but since the Trem and Phase wasn't really giving me the awesome ideas, maybe I should look outside the box a bit? Try something else?

Either that or it's verb.

Jacob

Cocked wah?