News:

Forum may be experiencing issues.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - jhigginb

#1
Yes on the Avalanche.   Great sounding pedal.


Sent from my iPhone using Tapatalk
#2
My wife an I have attempted to quit many times. She hit me up about two weeks ago to try again and the result was two aspire nautilus tanks and two tesla mods. So far so good but turned out she is allergic to propylene glycine (alcohol). So had to jump through some hoops to find the only company that carries true alcohol free liquids - virgin vapes absolute line.


Sent from my iPhone using Tapatalk
#3
Open Discussion / Re: Hey etchers. Impervious box?
June 28, 2014, 10:08:36 AM
Picked up the muratic at the hardware store (also found sometimes near concrete supplies for etching concrete) and peroxide was dollar store special as I wasn't sure how much I was going to go through. And of course copper clad board or anything else made of copper. I started off with about a cup of muratic and started adding in peroxide until I had about a half inch of fluid in the plastic container (used the zip lock containers for disposability, cheap, and doesn't react with the acid - the original plan was glass but thought my wife might get upset if I took the casserole dish)


Sent from my iPhone using Tapatalk
#4
Open Discussion / Re: Hey etchers. Impervious box?
June 28, 2014, 01:36:54 AM
The cupric chloride, if you want to try it, is muratic acid (pool supplies) and some hydrogen peroxide. Take that solution and etch a copper board or two and turns nice green color. I've been etching in the original mix for around 15 enclosures and just added more peroxide around enclosure 13 or 14. Boxes are nice and etched at about 15 minutes give or take. Depends in the etching mask from testing so far. Had one enclosure that had a lot if exposure and it was done in 8 minutes and was cut a little deeper than the others.  The heat being generated really did the job on that one and good thing I noticed the increased reaction. I'm guessing with that level of exposure and my usual timing, it would have gone almost through the top.


Sent from my iPhone using Tapatalk
#5
Open Discussion / Re: Hey etchers. Impervious box?
June 28, 2014, 12:57:45 AM
Which acid?  I'm using cupric chloride and has been very successful.


Sent from my iPhone using Tapatalk
#6
For a collosalus build. Etched and polished last night with paint following. Did a touch up on the paint this morning, killed an hour and started clear coats. . Still have 9 more different build enclosures to layout and etch. Maybe next weekend I'll have all of then done.


Sent from my iPhone using Tapatalk
#7
Introductions / Re: Hi
April 10, 2014, 02:48:49 PM
I think I fall under the lurker category. So here is my post :)

I build for my son. I spend too much time building things for him that I still haven't learned how to play, except a couple scales. Oh well, I really enjoy building. Next on the project list will be a few amps once the pedals are done.


Sent from my iPhone using Tapatalk
#8
Open Discussion / Re: MN3005's from synthcube
January 13, 2014, 09:18:26 AM
I've bought three from them.  All three were good but only one had a video test available. The other two were unmarked. And most definitely not the same guy. Synth cube is a group if guys state side.

Jamie


Sent from my iPhone using Tapatalk
#9
Open Discussion / Re: GT309G Sighted
November 08, 2013, 12:54:34 AM
Gotcha.


Sent from my iPhone using Tapatalk
#10
Open Discussion / Re: GT309G Sighted
November 08, 2013, 12:45:28 AM
I'm in. Sending pm


Sent from my iPhone using Tapatalk