Author Topic: deadringer build  (Read 2408 times)

nicobrewis

  • Diode Destroyer
  • *
  • Posts: 11
    • View Profile
deadringer build
« on: July 17, 2010, 03:45:28 PM »
Bad pic but this is my deardringer...the canary yellow just asked for this box !

[attachment deleted by admin]

nicobrewis

  • Diode Destroyer
  • *
  • Posts: 11
    • View Profile
Re: deadringer build
« Reply #1 on: July 17, 2010, 03:48:43 PM »
[/img][/img]

[attachment deleted by admin]

nicobrewis

  • Diode Destroyer
  • *
  • Posts: 11
    • View Profile
Re: deadringer build
« Reply #2 on: July 17, 2010, 03:52:55 PM »
A really fun build with really rewarding sonic results ...I used a "w" taper 20k pot on the tone and the warmth it added to the unit was noticeable to all....the 25k b is very bitey..

[attachment deleted by admin]

nicobrewis

  • Diode Destroyer
  • *
  • Posts: 11
    • View Profile
Re: deadringer build
« Reply #3 on: July 17, 2010, 04:03:19 PM »
more pics
sorry for all the pics just starting to get the hang of this

[attachment deleted by admin]

maysink

  • Solder Ninja
  • ****
  • Posts: 304
  • Erin (Irish; not female)
    • View Profile
Re: deadringer build
« Reply #4 on: July 17, 2010, 04:55:45 PM »
Lookin' good!
[nothing to see here]
-e

Haberdasher

  • Electron Doctor
  • *****
  • Posts: 2841
  • "El Duder-ino"
    • View Profile
Re: deadringer build
« Reply #5 on: July 17, 2010, 08:57:50 PM »
Dood, that is killer.

Where did you get those knobs?  I like that look.
I dig the case too.  Where did that come from?

thanks
Looking for a discontinued madbean board?  Check out my THREAD

FABRICATED PCB's FOR SALE:

pauloman80

  • Stompbox Star
  • ***
  • Posts: 192
    • View Profile
Re: deadringer build
« Reply #6 on: July 18, 2010, 06:02:59 AM »
Dood, that is killer.

Where did you get those knobs?  I like that look.
I dig the case too.  Where did that come from?

thanks

+1, that's a great enclosure!
--------------------------------------------------
Regards,
pauloman80

nicobrewis

  • Diode Destroyer
  • *
  • Posts: 11
    • View Profile
Re: deadringer build
« Reply #7 on: July 18, 2010, 07:37:02 AM »
The enclosure is a Hammond 1445N1602 ,basically an aluminium extrusion with a removable top and end-caps that I had powdercoated . They are nice cos you can assemble the whole unit on the lid ,as you can see on the one pic I did a (slightly untidy) dry run on a raw lid. The knobs I bought from a place here in South Africa called RS components..they have dealers all over the world ,the part # is 4664995

nicobrewis

  • Diode Destroyer
  • *
  • Posts: 11
    • View Profile
Re: deadringer build
« Reply #8 on: July 18, 2010, 08:23:26 AM »
Just to add a quick one... the 3DPDTnine- pin footswitch on the boost side can easily be subbed by a six-pin 2DPDT  It wont affect the bypass at all .Hope it helps ..where I live we have to bring the 9,s in from the USA ...aah life in Africa ..pic with diagram included !

[attachment deleted by admin]