Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - andregarcia57

Pages: [1] 2
1
General Questions / Project Volume Pedal Boss buffer
« on: April 13, 2023, 07:07:48 AM »
hey guys, first feel free to move to the correct location of this post.

I'm thinking of making a buffered volume pedal, is it correct to do it this way?

I put the 250k potentiometer between the buffers. which potentiometer ideal for this circuit?
thanks

2
Open Discussion / Pastyface with gate
« on: August 24, 2022, 08:55:25 AM »
hello guys, I just built NPN pastyface, it sounds good but I can't through the trimmer make it sound with gate, would there be any way to do this by changing some resistor value?

3
General Questions / More Bass Current Lover
« on: September 18, 2021, 06:45:49 PM »
I built Current lover (Mistress) from madbeans, but I think it lacks some bass, or what can I change? Thanks

4
Requests / Marshall - Shredmaster more volume
« on: May 18, 2015, 09:40:16 PM »
because shred volume is so low?
some mod is to increase final volume?

5
General Questions / Re: ICL7660SCPA and ICL7660CPAZ
« on: January 13, 2015, 05:27:24 AM »
here I only found the ICL7660CPAZ and the MAX 1044 CPA

MAX 1044 CPA can do the job in sunking?
thanks

6
General Questions / Re: ICL7660SCPA and ICL7660CPAZ
« on: January 12, 2015, 04:37:57 PM »
The ICL7660S (ICL7660SCPA) model has the Boost pin (pin 1).  That is what the Sunking II calls for.  The standard ICL7660 (ICL7660CPAZ) does not have it.

I should not use ICL7660CPAZ in sunking?

7
General Questions / ICL7660SCPA and ICL7660CPAZ
« on: January 09, 2015, 04:55:58 PM »
I'm mounting sunking II

There are some different between ICL7660SCPA and ICL7660CPAZ?
thanks

8
Build Reports / Re: sucking II and stock klon
« on: January 04, 2015, 04:32:34 AM »
No, those values are incorrect. The values you listed came from the original schematic release of the Klon which had errors. That schematic was later revised in April 2009. The Sunking uses the corrected values.

would this correct?

9
Build Reports / sucking II and stock klon
« on: January 04, 2015, 03:11:15 AM »
hello
I have just received sunkin ii and would like a help to set up stock klon.
R3 - 4k99
R12 - 27k
C2 - 150n
C3 - 330N
C4 - 180N
C5 - 47n
C7 - 68n
C12 - 6n8
C13 - 18n

this would be in stock klon sunking II?
thanks

10
General Questions / Dynacomp + Tube Screamer
« on: August 12, 2014, 10:18:10 AM »
anyone have a PCB that would Dynacomp and tube screamer on the same PCB?
thanks

11
General Questions / Re: route 66 compressor ?
« on: August 12, 2014, 10:16:23 AM »
anyone have a PCB that would Dynacomp and tube screamer on the same PCB?
would be almost the same design ....

12
Build Reports / Re: Madbean Wolf Shirt (Foxx Tone Machine)
« on: April 03, 2014, 01:22:33 PM »
today I had a problem with two pedals.

Wolfshirt + Univibe.

same vibe off the effect of this on the bottom.

used 3PDT and I made several calls en failed.
after several attempts I gave a look at some filter pedals. and decided to put 100ohms in early 9v pedal. solved!

gets the hint

13
General Questions / Capacitors for the KingSlayer:
« on: January 31, 2013, 01:46:44 PM »
I have a doubt Capacitors for the KingSlayer....

I would like to subistituir some electrolytic capacitors by tantulum even for reasons of space.

C3, C10, C25, C26 - I change to tantulum?
C11, C16, C9 -  I change to Panasonic

is correct to do this?

14
Build Reports / Suking (klon) capacitor
« on: January 31, 2013, 08:39:34 AM »
hello okay guys?
I am wanting to use all 1uf and 4.7uf Tantalo for reasons of space, sonically change anything?
thanks

15
Tech Help - Projects Page / Re: Aristocrat wiring diagram?
« on: December 28, 2012, 06:41:12 AM »
I NEED TOO

andrediscos@hotmail.com
thanks!

Pages: [1] 2