Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jjanssen1

Pages: [1] 2
1
Open Discussion / Re: what are you guys listening to at the moment?
« on: April 28, 2020, 07:45:42 AM »
Nonagon Infinity, Murder of the Universe, Polygondwanaland, Infest the Rats' Nest, and (the soundtrack of) Chunky Shrapnel - King Gizzard & the Lizard Wizard.

Skip Tracing, Timeline - Mild High Club.

Sketches of Brunswick East - King Gizzard & the Lizard Wizard + Mild High Club.

Perform the Most Curious Water Activities - Post Animal.

Congratulations, Little Dark Age - MGMT.

Man It Feels Like Space Again, The Weather - Pond.

High Visceral Pt.1, High Visceral Pt.2, And Now For The Whatchamacallit - Psychedelic Porn Crumpets.

The Dark Side Of The Moon, Meddle, Wish You Were Here - Pink Floyd.


Anyway, these are just a few of the albums I'm listening to on repeat at the moment. I know that my overall taste in music is quite limited, it's just that, no matter how hard I try, I seemingly cannot broaden the range of genres I listen to. Oh well, I guess I'll just be a habitual Neo-Psychedelia listener for the time being.

Cheers,
Joshua.

2
Build Reports / Re: Madbean Honeydripper
« on: November 17, 2014, 03:26:29 AM »
How's the sound?

3
Open Discussion / Re: What kind of pot is this?
« on: November 13, 2014, 02:33:55 PM »
I would say it's a 100K linear potentiometer

4
Global Annoucements / Re: Dirtbag Deluxe 3?
« on: October 30, 2014, 04:33:53 PM »
I'm gonna go out on a limb and say the dirtbag isn't gonna be released in October... :(
Agreed

5
Open Discussion / Re: Well, there goes another $600
« on: October 25, 2014, 02:13:09 PM »
I'm hoping these will last me at least 5-6 years...probably longer if I take good care of them.
The Weller soldering iron I was using before I (recently) got my Hakko FX-888D was over 20 years old with regular use from my Dad (when he was still an electronics engineer)
You can easily do SMD on the Hakko FX-888D but could never do it on the Weller
Cheers
Joshua

6
General Questions / Re: Vero newboe problem
« on: October 23, 2014, 01:49:16 AM »
Whould it be possible for you to post some pictures of the board and the layout your using
Cheers
Joshua

8
Introductions / Re: Greetings
« on: October 17, 2014, 05:23:15 PM »
Welcome to the forum,
If you want to give DIY guitar pedals a go I would recommend one of Madbean's fuzz projects to start with.
Have fun!
Joshua

9
Tech Help - Projects Page / Re: Harbinger One LED
« on: September 23, 2014, 03:10:30 AM »
Hi,
Do you know what the voltage drop across the LED is?
Cheers
Joshua

10
Tech Help - Projects Page / Re: fx on-off switch
« on: September 18, 2014, 06:33:00 PM »
I once went to a music shop and one of the staff there was using some alligator with a standard tip/sleeve guitar cable to find out what combinations worked to switch reverb on/off and to switch between the channels on an old fender amp I'm pretty sure it was. So if the combination is tip and sleeve momenterley to switch between reverb and non-reverb then you go and get a spst momentary switch to turn reverb on/off.
Hope this helps
Joshua

11
Requests / Re: 1590LB pedals
« on: September 17, 2014, 04:23:07 PM »
what would you like to see done?
Something like a Phase 45 or a Phase 90, basically  any one knob phaser

12
Requests / 1590LB pedals
« on: September 17, 2014, 04:03:03 PM »
Hi all,
Just a thought ...
Could madbeanpedals make tiny smd pedals to fit inside the 1590LB enclosures available from places such as:
 http://pedalpartsaustralia.com/index.php?main_page=product_info&products_id=125
Cheers
Joshua

13
General Questions / Re: Adding tap tempo to ZeroPoint Micro II
« on: September 05, 2014, 03:07:35 PM »
You need a taptation.  You can get the ICs at diystompboxes.  I also believe jmkpcbs has some great boards for the taptation with will work with the zero point and the ICs
Thanks for the help.

Joshua

14
Tech Help - Projects Page / Re: Zero Point SDX LED problem
« on: September 05, 2014, 05:37:17 AM »
Hi,
are you sure that you have your led cathodes going to the right pad for the leds
Hope this helps
Joshua

15
General Questions / Adding tap tempo to ZeroPoint Micro II
« on: September 04, 2014, 07:17:36 PM »
Hi All,
Currently I am building a Zero Point Micro II and I am thinking about adding tap tempo to it.
Does anyone know how I can easily add tap tempo to this project.
Cheers
Joshua

Pages: [1] 2