Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mickey.bellinello

Pages: [1] 2 3 4
1
General Questions / Re: AionFX Redshift Phaser Issue - Help Needed
« on: June 03, 2021, 02:43:05 AM »
Hi to all, rececked all and all seems ok.

I asked in various forum and it seems that is "normal operation".

Seems a bit strange but it is.

Thanks for the help! ;)

Another question, I added a rate pulse led using this method:

9V -> LED -> 2N5087 emitter,
2N5087 base to Q4 Emitter
2N5087 Collector to 47k R to ground.

Not super smooth but it pulse.

Any ideas to smooth it out a bit?

Thanks

2
General Questions / Re: AionFX Redshift Phaser Issue - Help Needed
« on: June 01, 2021, 07:40:06 AM »
And if feedback setting is low, everything works ok?

Exactly, if the feedback is before 50% I have full volume. If I crank it the volume goes down...

It seems pretty strange.... I checked the pot and it works properly...

3
General Questions / AionFX Redshift Phaser Issue - Help Needed
« on: June 01, 2021, 06:12:18 AM »
Hi to all!

I just built a redshift phaser. It works but to me there is a problem with the feedback knob.

When i turn it clockwise, after 50%, i got a big volume drop and it seems very strange.

Hereís the kit instruction:

https://aionfx.com/app/files/docs/redshift_documentation.pdf

Any ideas? What can i check??? I have no voltage reference unfortunely.

Thanks

4
Tech Help - Projects Page / Re: Aquaboy-AquaPuss specs Info
« on: April 16, 2021, 04:06:54 AM »
Using the Aquababy schematic as a reference:

R11 - 470R --> 150R
C2, C7, C16, C23, C26, C27 - 1uF --> 10uF
C14 - 82nF --> 100nF
C28 - 100nF --> 220nF

Great! Thanks So Much!

5
Tech Help - Projects Page / Re: Aquaboy-AquaPuss specs Info
« on: April 14, 2021, 10:04:21 AM »
thanks so much!

6
Tech Help - Projects Page / Re: Aquaboy-AquaPuss specs Info
« on: April 14, 2021, 05:09:41 AM »
Sorry for the double reply. Cannot find the schematic in the forum. Some of you has the aquapuss corrected schematic? So i can take a look and comparison and modify my madbean delay? Thanks

7
Tech Help - Projects Page / Re: Aquaboy-AquaPuss specs Info
« on: April 14, 2021, 01:44:16 AM »

Values to be changed in the dm-2 schem:

R7 - 10k - 1k
c8 - .082 - .1
c21 - 1u - 10u
c14 - 10u - 1u
c22 - 10u - 1u
r34 - 470ohm - 100ohm
c30 - 1u - 10u
r39 - 100k - 10k
c25 - 100u - 47u
c32 - 220u - 330u"

So, not only the 1uf-10uf caps and 47 - 47.5 resistors?

9
Tech Help - Projects Page / Aquaboy-AquaPuss specs Info
« on: April 11, 2021, 02:36:31 PM »
Hi to all,

I built a working Aquaboy Delay some times ago using standard dm2 components values. Itís some days that iíd like ti try it with ďaqua pussĒ components value but i have no idea of what i can get with theese mods. Can someone tell me the differences between the stock and the ďmodĒ version?

THANKS

10
I recently ordered four of the "nos" mn3101 from Banzai and they appear to be mn3102 as well.

Hi have you tried buying it from Musikding? I see that they have several kits of pedals that include MN3101 chips. ;)

11
Global Annoucements / Re: Bass Series is out
« on: March 17, 2021, 12:49:06 PM »
Just finished JunkTrunk an Gas Tank! Simply Amazing!!!

Do you plan to realize some other bass stuff???

It would be great!

12
Tech Help - Projects Page / Re: Junk Trunk massive volume drop
« on: March 08, 2021, 12:48:53 PM »
Hi! I see that there is a bridged pin in the (refer to the photo) last ic and probably in other place.


13
Tech Help - Projects Page / Re: Gas Tank + Junk Trunk Boxing Question
« on: March 08, 2021, 12:46:38 PM »
Did you finish the board(s) for this yet? I just finished up a junk trunk and am experiencing a massive volume drop with it engaged. It passes signal, and the effect is working, but the volume drop is to the point where it's currently unusable. All my voltages are correct per the build doc, so I'm curious if you've experienced anything similar? Thanks!

Hi! Really? Did you check that all works right?

At the moment iím still waiting to receive the pcb (i live in italy so it takes times to arrive).

When iíll receive it iíll built it immediately and iíll tell you what happens;)

14
Tech Help - Projects Page / Re: Gas Tank + Junk Trunk Boxing Question
« on: March 02, 2021, 08:05:22 AM »
Thanks So So Much! :)

15
Tech Help - Projects Page / Gas Tank + Junk Trunk Boxing Question
« on: March 02, 2021, 05:50:25 AM »
Hi to All!

Very simple question. I ordered a Gas Tank and a Junk Trunk PCB, I'd like to box them in one enclosure with two switches for activation. I don't have the exact measures of the pcbs so I don't know which enclousure order to fit them without problems. Any suggestion?

Thanks

Pages: [1] 2 3 4