Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Hexjibber

Pages: [1] 2 3 ... 18
1
Build Reports / Re: Coda Effects Black Hole
« on: June 17, 2020, 11:03:09 AM »
If the circuit were to be adapted to run at 18v, how would that biasing need to be changed?

I have to confess I have not even the slightest idea! Maybe a question for Benoit over at Coda Effects?


Sent from my iPhone using Tapatalk

2
Build Reports / Re: Coda Effects Black Hole
« on: June 17, 2020, 11:01:40 AM »
Now the real important thing. This build is awesome! The graphic gives a 3d look at the pedal.

Thanks!


Sent from my iPhone using Tapatalk

3
Build Reports / Re: Coda Effects Black Hole
« on: June 17, 2020, 11:00:40 AM »
Love that enclosure design/paint job! It's insane that you got such ripping tones without the transistors soldered in...
Haha! I managed to get these super rare invisible ones, to say they have the mojo factor would be an understatement! Very hard to come by owing to the fact you canít see them, getting the orientation right was tricky to say the least!


Sent from my iPhone using Tapatalk

4
Build Reports / Re: Pig Butt - 1st Pedal Build
« on: June 01, 2020, 02:12:54 AM »
That is a really quite excellent first build, inside and out! Really impressive! Keep it up!

5
Build Reports / Re: Dead End FX Grimafuzz
« on: June 01, 2020, 02:10:59 AM »
Thanks guys, had more of a sit down session with this pedal over the weekend, I'm really into it now!

6
Build Reports / Re: Aztec Factory
« on: May 30, 2020, 11:11:15 AM »
Thanks guys, pretty sure my mate will be really chuffed with this when he gets it!


Sent from my iPhone using Tapatalk

7
Build Reports / Aztec Factory
« on: May 29, 2020, 04:12:52 AM »
Aztec Factory built on FuzzDog Filth Fack board.

This was a request from a mate and Iíd not built one before despite being curious about them. Have to say I loved it when I fired it up! Knarly fuzzy goodness! Added the fat switch for extra boeuf. Need to build my own one now! Think I might go for the more knobs version though.

Reverse etched and painted then glitter sprayed






8
Build Reports / Re: PedalPCB.com Chicken Head
« on: May 28, 2020, 07:11:59 AM »
Awesome man, thanks for sharing your process! I've been thinking about trying my hand at some painting but really have no idea how to go about it so really interesting to see! Looks like you need a steady hand and a good eye, nice work!

9
Build Reports / Re: Dead End FX Grimafuzz
« on: May 28, 2020, 07:08:43 AM »
Thanks guys!  8)

10
Build Reports / Dead End FX Grimafuzz
« on: May 28, 2020, 02:42:36 AM »
Hellooo out there, hope everyone is staying well!

Latest project is the Grimafuzz from Dead End FX. I recently built the PedalPCB Super Heterodyne Receiver and really liked the fuzz section of it, a Madbean forum member was kind enough to point me in the direction of a DeadEndFx board of just that section of the PLL so got on it straight away! Itís a thick, nasty, somewhat gated fuzz thing and I dig it! The board also has some cool features such as a blend pot so it can be used on bass.

Reverse etched and then painted, also tried some splatter painting for something a bit different, I really like how it came out.








11
Build Reports / Re: EAE Mojo Titan
« on: May 17, 2020, 11:58:03 PM »
How strong is the enclosure? Think it will hold up to a fair amount of use? Always wondered about those boxes.
I think it seems ok, definitely a lot thinner than Hammond boxes but I tried applying a fair amount of pressure when I pressed the switch and there wasnít really any give as such. Time will tell tbh!


Sent from my iPhone using Tapatalk

12
Build Reports / Re: EAE Mojo Titan
« on: May 13, 2020, 12:00:56 AM »
Cheers guys, was a tricky etch tbh and the aluminium reacted quite differently the Hammond boxes Iím used to. Initially I wasnít sure if it was working at all!

Also, not sure if you can see from the photo of the knob labels, but I inadvertently ended up getting bevelled lettering! The etchant must have been nibbling away at the edges of the letters, it looks pretty cool tho I think!


Sent from my iPhone using Tapatalk

13
Build Reports / Re: EAE Mojo Titan
« on: May 10, 2020, 01:13:25 PM »
Man, that looks so pro.  Great build!
Thanks!


Sent from my iPhone using Tapatalk

14
Build Reports / Re: EAE Mojo Titan
« on: May 10, 2020, 12:39:55 PM »
that looks so slick and clean. well done graham

Cheers Felix!  8)

15
Build Reports / Re: EAE Mojo Titan
« on: May 10, 2020, 09:49:55 AM »
That looks great! Where did the enclosure come from?
Thanks! Itís from Mouser;

https://www.mouser.co.uk/ProductDetail/LMB-Heeger/MDC-642-PLAIN-ALUM?qs=xp7S8dfB2cbsXlxTu%2FTXtQ%3D%3D


Sent from my iPhone using Tapatalk

Pages: [1] 2 3 ... 18