Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - BuGG

Pages: [1]
1
Open Discussion / Anyone have one of these knobs?
« on: July 20, 2018, 02:09:44 PM »
Anyone have one of these knobs, or a pedal that uses them?  I'm just curious about the size (maybe up against a 1510 or MXR?)... 

I've contacted Daier for a datasheet/drawing but they apparently can't provide one for this one.   ::)

It looks like some sort of Davies clone but I can't figure out which one.




2
Open Discussion / Help me identify this SMD transistor
« on: November 19, 2017, 09:04:33 AM »
Anyone familiar with an NPN SMD transistor with the marking "1RM" ?

I'll ship a free PCB to whoever identifies it first.    ;D

EDIT: Identified, thanks!

3
Open Discussion / International shipping of PCBs
« on: June 25, 2017, 11:52:10 AM »
Could someone show me the type of envelope/mailer Madbean uses to ship a PCB internationally?

I've managed to pull it off with bubble mailers in the past but never felt very confident about them....  I have a small handful of boards to ship overseas and was curious what the best method would be.

4
Open Discussion / VFE Pedals is releasing schematics
« on: August 01, 2016, 10:27:59 AM »
Howdy guys, haven't seen this mentioned here before and thought you'd like to know...

Peter from VFE Pedals is releasing the schematics to all of his Standard Series pedals to the public.    I'm working with him to help get them cleaned up and unified.   

The overdrives have been posted, distortions will be next.  :)

https://www.facebook.com/VFEpedals/photos/?tab=album&album_id=1024502897599591

5
Open Discussion / Mammoth Screen Printing?
« on: May 02, 2014, 10:40:34 AM »
Has anyone here had any screen printing done by Mammoth lately?

I'm planning to get a batch of 10 enclosures and want to know what others think of the quality of work?

6
Build Reports / MXR Distortion II
« on: April 09, 2014, 10:06:48 PM »
Finally got around to building my MXR Distortion II clone...   I know, I know, I shouldn't have used the MXR name but I wanted "authentic" cosmetics.    ::)

This one is true bypass, runs on 9-18VDC, and has In/Out jacks on opposite sides (vs same side like original)

Ideally I'd like to work up an etchable layout for this one, it's currently built on stripboard and I'm not extremely enthused about that.


7
Open Discussion / Tayda PCB Manufacture
« on: December 19, 2013, 02:57:57 PM »
Has anyone else seen this!?       :)

http://www.taydaelectronics.com/custom-pcb

8
Tech Help - Projects Page / DeadRinger FCV Switch
« on: December 07, 2013, 02:56:46 PM »
When the DeadRinger is in Comp Cut mode are the Flat Mids components supposed to be active?

9
Open Discussion / Tayda 1590A Dimensions
« on: November 07, 2013, 11:24:37 AM »
Does anyone know if the 1590A enclosures coming from Tayda are a different size from all others?

None of the 1590A drilling templates I have printed seem to fit the enclosure properly, it seems mine is about 1/2" taller than the template.   I've tried several, including the Madbean Sprout template.   

I can wrap the template around and make it work, but it doesn't fit like the templates for other enclosures have.  Am I missing something?

10
Open Discussion / Layout/Component Placement Tutorials?
« on: September 17, 2013, 10:44:58 PM »
I know this is a rather tough subject to "explain", varies from project to project, and is more of an acquired skill, but does anyone here know of any good tutorials or videos on the subject of PCB layout and component placement?

I'm not referring to technically operating the software itself, but possibly some tips/tricks to finding good placement of the components?

I've picked up some useful info/pointers from various members but was wondering if there were any "tutorials" similar in quality to Jacobs videos on learning Eagle?

I'm considering grabbing a copy of RG Keens book "PCB Layout for Musical Effects"...

Pages: [1]