Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Stomptown

Pages: [1] 2 3 ... 98
1
Open Discussion / Re: Memory Man Artwork for Total Recall Build
« on: February 14, 2022, 11:34:39 PM »
Hey Jon!  Oh yeah, hey that'd be awesome... thank-you!
PM Incoming :)

No problem.  Iíll send you the files in a sec.  Keep in mind the 3pdt location on my graphic might conflict with the Total Recall PCB.  I think Brian is working on a new/compact layout though so that would probably work fine.  The one I built used althe old school Dirtbag PCB!

2
Open Discussion / Re: Memory Man Artwork for Total Recall Build
« on: February 14, 2022, 11:30:30 PM »
Wow! That looks great! Did you recreate the type manually? I didn't think that it was an available typeface.

Yeah, it was a major pain in the butt. 😂

3
Open Discussion / Re: Memory Man Artwork for Total Recall Build
« on: February 14, 2022, 07:13:09 PM »
Will this work?  PM me your email address if you want the pdf


4
Open Discussion / Re: RIP - haveyouseenhim
« on: February 11, 2022, 01:32:48 AM »
Man, this is really sad news. RIP Mike.

5
Open Discussion / What is everyone doing????
« on: February 02, 2022, 11:22:05 PM »
Iíve been in a lull for the last 9 months it so.  I did finish a Partscaster (tele) last fall that I should post on here.  I also have several half built pedals and an amp in the works but I canít find the time/energy to finish them.  On top of that, we just put an offer in on a home so Iím most likely going to be working on DIY projects of another kind for the foreseeable future.

Hereís my 2008 SG Classic w/ chunky neck:


6
Open Discussion / Re: This has to end
« on: January 22, 2022, 08:56:57 PM »
My workbench has been covered in cobwebs for the past year and a half.  Iíd take a picture, but Iím too damn tired to go out there!  😂

7
Open Discussion / Re: Merry Christmas everyone
« on: December 24, 2021, 02:21:57 PM »
Merry Christmas everyone!

8
Open Discussion / Re: Small bear retiring
« on: September 28, 2021, 01:31:18 AM »
I know this will be an unpopular thing to say, but Tayda carries a lot of 9mm lots now and the few Iíve gotten from them have been fine.

I think the reality of this is that there is demand for a lot of this stuff and a couple of places will probably step up and attempt to fill the gaps created. There is a demand and Iím sure it will be filled. Iíll be sad to not have smallbear, but my solder will continue to flow.

The only question is, how much wire to stockpile before he closes for good.

I expect I am the outlier, but in my case, Tayda carries the wrong 9mm pots.  They carry the PC mount right angle version and I prefer the typical PC mount, which is more difficult to find.

CE distribution (distribution arm of amplified parts/antique electronic supply) sells the straight pin 9mm Alphas. Iím guessing they donít carry half the values that Steve does but it might be an option worth checking out.

9
Open Discussion / Re: Small bear retiring
« on: September 22, 2021, 08:28:23 PM »
Man, what bittersweet news.  Iím very sad for the DIY community but happy for Steve.  It will definitely be interesting to see how this unfolds.

10
General Questions / Re: If all my IC voltages are correct...
« on: June 20, 2021, 08:35:07 PM »
Why are these pads soldered? 


11
Open Discussion / Re: Happy Fathers Day!
« on: June 20, 2021, 04:29:05 PM »
Happy Fatherís Day guys!

12
Open Discussion / Re: First Unsuccessful Build
« on: May 23, 2021, 12:33:05 PM »
If you have a multimeter with a continuity tester, you can check for broken connections by touching one probe to part where pad is lifted and other probe to leg of part that it should be electrically connected to according to schematic or PCB traces.  If the parts are connected as they should be, the meter will make a continuous sound. Also, did you rock it before you boxed it (i.e. test PCB before putting it in an enclosure)?  Itís possible the mistake has to do with the wiring or something is shorting out on the enclosure.

13
Open Discussion / Re: Anyone else get the Covid Vaccine?
« on: May 07, 2021, 03:54:23 PM »
My wife and I had Moderna #2 yesterday.  I had a mild headache and arm pain after about two hours and thought I was mostly in the clear. Woke up at 3AM with terrible head and body aches, fever, chills, nausea, and dizziness. My wife is now dealing with body aches and dizziness but sheís doing better that I am overall. Hopefully we start feeling better by tomorrow.

14
Open Discussion / Re: Suggestions for a newby
« on: May 05, 2021, 11:40:41 PM »
There's so many pedals I managed to troubleshoot with a multimeter that gives you a noise when you have continuity, an audio probe and a delay pedal that can also loop a riff, so you can trace your signal through the circuit.

This!  Definitely make sure your DMM has a continuity setting.

15
Open Discussion / Re: The pedal movIe
« on: May 05, 2021, 11:21:32 PM »
Iím going to try to watch it this weekend. Last weekend I watched the new Dave Grohl doc What Drives Us and really enjoyed that.

Pages: [1] 2 3 ... 98