Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dbharris

Pages: 1 2 [3] 4
31
Mods / Re: Any Dyna Comp Mods?
« on: September 02, 2011, 12:24:47 PM »
It depends what version dyna comp you have.  The newest revision is pretty different than the original (I have one and decided to build a vintage ross clone instead of modding it).  But you should be able to find some stuff online that will apply to it.

32
Audio/Video Demos / Re: LowRider
« on: August 22, 2011, 05:32:09 PM »
Sounds awesome!  I want this and a dipthonizer so bad lol

33
General Questions / Re: Pork Barrell Component query
« on: August 01, 2011, 12:26:56 PM »
They have always emailed me back within 2 days, it usually takes about 3/4 of a day I think because of the time difference.  I know that they have several contact email addresses depending on what you need from them.  Maybe check again who you sent it to and re-send it to customer service or order inquiry. I forget what they call it exactly...

34
General Questions / Re: Pork Barrell Component query
« on: August 01, 2011, 08:24:49 AM »
My experience with futurlec is that if you are waiting a month it is because they don't have a part or parts you ordered in stock.  They are pretty good if you email them, but they never take the first step to tell you that they won't be able to ship until their stock comes in.  Sometimes you can change the part to something similar and get it shipped right out.

35
Build Reports / Re: Lonestar amp switch
« on: July 07, 2011, 05:09:21 PM »
Thanks for the infos, I kinda figured it probably would not work they way I hoped.  It's no big deal to have the normal LED scheme.  I usually have the two channels set so different you don't really need an LED anyways to know which is active.  Now I don't have to waste time trying something that wont work. 

-Dan

36
Build Reports / Re: Lonestar amp switch
« on: July 07, 2011, 01:48:24 PM »
That looks great!  I have the same amp, I am planning on doing up a switch in a 125B with a second jack and third switch to control the reverb too.  The only different thing I was considering doing was replacing the red channel LED with a red/green dual LED.  So that on the clean channel the switch LED would match the amp panel LED.  I'm not sure if current flows down that line to light the LED in that state of switching, so I guess I will just have to do some good old trial and error.

37
Requests / Re: A more uber road rage...
« on: May 17, 2011, 03:56:38 PM »
I think it would be cool to have that option.  I was thinking about doing something like that on perf in the range of 36-48 volts for pedals that use amp topology with fets instead of tube triodes.  I thought it might give some good headroom and dynamics. 

38
Requests / Re: Smaller Dipthonizer
« on: May 12, 2011, 02:29:21 PM »
Thanks Brian!

39
Requests / Re: Smaller Dipthonizer
« on: May 11, 2011, 05:21:00 PM »
OK thanks so much!  Sorry to hear you had some problems with the prototype.  Juansolo mentioned in the OP and I've also heard a few guys on BYOC say that the original layout has some errors.  That's why I stayed away from building this at first.  So if the schemo looks correct maybe looking at the thread on BYOC will help a little.  Good luck!

40
Requests / Re: Smaller Dipthonizer
« on: May 11, 2011, 01:53:49 PM »
Hey Brian,

I know you've been super busy lately.  I was wondering if there was any progress on this project?  Even an official BOM for your board would be awesome.  I'm waiting on placing a small bear order for whatever I need but don't have for a dipthonizer and a forumvibe.

Thanks!

Dan

41
Requests / Re: Smaller Dipthonizer
« on: April 13, 2011, 02:53:24 PM »
Ok awesome, I need to remember to grab some of those LT1054s on my next order.

42
General Questions / Re: Sunking a/b with klon
« on: April 12, 2011, 07:44:55 PM »
I got the same ones from futurlec.  They are NOT 1n34a, here is a thread at BYOC talking about it http://www.buildyourownclone.com/board/viewtopic.php?f=13&t=29809

They are shottky diodes, with about .31 forward voltage.

That being said, if you like them then great go with it.  I now have 100 of them so I hope I like them too...

43
Requests / Re: Smaller Dipthonizer
« on: April 12, 2011, 07:27:09 PM »
Awesome, thanks madbean!  So it looks like you will need a separate road rage board to go along with this board right?

44
Build Reports / Re: Aquaboy - Amphitrite Delay (Finally!)
« on: April 11, 2011, 07:48:31 AM »
Wow that is really impressive!

45
Requests / Re: Smaller Dipthonizer
« on: April 10, 2011, 11:15:06 AM »
+1 I have been wanting to build this one for a while.  It's first on my to do list once I finish all the projects currently on my bench...

Pages: 1 2 [3] 4